Search results for query: *

A BCM400 R4.0 customer replaced his WLAN 2210 set with a 6120 set, but the new set has very bad voice quality. When you talk to someone, the other end will always hear choppy voice, but you end is always fine. The signal is OK. Changed codec did not make any change, I think the product doesn't...

This is kind of urgent, here is some background: BCM50 R2.0(patches are up to date), PRI Lines(from Bell), Tollfree 800#(from Primus). Most of time when you dial their 800# and get to the AA, you punch the extension#, sometimes you are just ignored, the AA keeps playing; sometimes says 'this is...

Base on the other threads, I'm trying remotely use a IP softphone 2050. Here is some background: BCM50 3.0 in the office, in the firewall NAT setting: forwarding UDP 7000, UDP 28000-28511 and UDP 51000-51063 to BCM50, meantime allow traffic through all those ports to BCM in the firewall setting...

We have a customer using BCM400 R4.0, SU patches applied, including the psm patch, but recent the "Out of memory" alarm comes up again. Once restart BCM, it is last for couple of weeks then this alarm shows. Anyone has good tips for us? Thanks. Always learn from someone, something and...

Anyone who ever had this type of issue before with a BCM50? Customer complains some time when caller reached their AA and tried to press # go to company directory or press ** go to VM, but got no response. This happened intermittently, and the lines carrier inspected their lines and say nothing...

I tried and found the i2050 software phone v3 is the only version I could use in Vista? I tried v2.255, 260, did not work. Actually, install and setup no problem, but when you use it the voice is too bad. Once changed to v3, worked like charm. Any one has other idea? Always learn from someone...

Has anyone ever made a BCM50's and works? We had BCM50 R1.0 failed, seems like the HD crashed, could not get it back even with level 2 reset. When we open it and suprised that there was a 3.5 inch desktop SATA HD in it same as BCM400 (IDE HDD). So I'm wondering if anyone who ever done a ghost...

Hi pros, Has anyone ever successfully used ghost to make a new BCM 4.0 Hard drive using the 3 CDs came with the 4.0? Does the parameters for 3.7 image still works for 4.0? Like to hear your achivements. Thanks. Always learn from someone, something and somewhere...... Michael C www.tomkin.ca

Has anyone had same issue before? I have used 2 Contivity 1010 to build a branch tunnel between the main site with BCM400 R4 and a branch with 2 i2002 IP sets. The phone could come up, but it works perfect just about the first couple of minutes. After that once you press intercom, there is no...

I have used 2 Contivity 1010 to build a branch tunnel between the main site with BCM400 R4 and a branch with 2 i2002 IP sets. The phone could come up, but it works perfect just about the first couple of minutes. After that once you press intercom, there is no dial tone, when you dial someone...

Any one who knows why VPN tunnel keeps dropping and reconnecting? We have a customer site, has 3 locations, using 3 Nortel BSR222 VPN Router connect to each other via Branch Office Tunnel. Almost every 5 to 10min, the VPN tunnel is reconnecting, could not last long. The rekeying time (or SA...

A customer has WSS2360, with 2330A APs and 2211 IP sets. The big issue is when someone has the set talking and walking from one area to another, the 2211 doesn't automatically swap the AP from the far one to the closer AP, and the conversation got dropped or in and out. Anyone has some idea or...

We have a customer had some IP sets like i2002, i2004s. Sometimes the sets just got disconnected even during the calls, and would not come back for about 20 min. Meantime, the BCM50 is running fine and network is good too, and they have PC connected to the sets. Could anyone tell me what to...

We have a customer site, has Nortel BSR222 on both locations and had branch tunnel built up. Customer reported that sometimes BOT disconnected and didn't come back for like 20 min, and then back on. At mean time the internet is OK on both locations. Any idea ehat should I check? Always learn...

In last 2 weeks, I installed a Contivity 1010 and Contivity 1100 for 2 customers. Everything is working fine other than 1 customer could not log in any FTP sites, another customer could not access certain websites such as www.msn.com, hotmail.com... Both these 2 customers use ADSL. I believe...

We have a customer has 3 locations: in Centre Office has a BCM50 2.0 and a Nortel BSR222 VPN router; there are 2 other locations have same BSR222 and using VPN Tunnel to the Centre Office. At each remote site has an 1120E IP set, connecting to the BCM50, one is x230, another is x240. Issue is...

Our cutomer has 2 locations A & B using Contivity VPN tunnel connected. A site has BCM and WSS2360 for 2211 WLAN sets. Now B site has APs installed, base on WSS2360 configuration guide, I need config DHCP option 43 in DHCP server which is Contivity 1010 at B site for APs, so that AP can talk to...

I set up a BOT between Contivity 221 and a 1100. It is up and running, but I can only ping and access the remote contivity 1100's interface 0 (LAN) IP address and management IP address. No any of other LAN PCs is accessible. When set up BOT I already configureed the local network and remote...

I tried my best to set up a BOT between a SR1001 and Contivity 221, but had no luck. But I can easily set up BOT btween a Contivity 221 and 1100 wihtout problem. There got to be something special I don't know in SR1001 VPN set up. Any one who had experience within SR1001 config please give me...

I'm new with T1 set up and secure router as well. The situation is simple, I have these info: P2P T1 IP address(service is up), public IP block (5 IPs), SR1001 router. I deployed T1 IP to WAN port, 192.168.0.2 to LAN port, so what else I need to do to complete this job? The LAN user has no...