Search results for query: *

Can the system boards be switched between the SF15K and the SF6800, if the CPU's speed are the same? Thanks

Are the HP or IBM LTO3 drives arbritrated loop attached only? These drives are located in a L700 and I looking at the connectivity to a McData 6064, which support fabric only. Thanks,

Has anyone setup ZFS on SPARC archtitecture? Is ZFS mirroring supported on SPARC, I know it is on X_86. I suppose SVM is the best to use on your root filesystems and then use ZFS for the others filesystems. Thanks

Trying to setup a new McDATA 6064 and can't comunicate with the maintenance port (DB-9) located on the backside of the 6064. Tried these settings: V100 terminal 115200 baud, 8 data, 1 start/stop bit, no flow control used modem cable and a crossover (null modem) cable Reduced baud down to 4800...

Does the st.conf file require entries for HP LTO3 drives? st.conf patch 108725-24 is installed. Thanks

Running Solaris 8 and I will install st.conf patch 108725-24 prior to the drive switch. There are 10 LTO 1 drives inside the L700. I will also upgrade the L700 for the LTO 3 drive. I am switching one of the LTO drive. Presently the st.conf file has entries for the LTO 1 drives, will the LTO 3...

Planning on upgrading from Solaris 8 to Solaris 9. . Boot disk is mirrored (SDS) . Have 35 metadevice (SDS) I can unmirror the boot disk ONLY and do a regular upgrade or leave the boot mirror intact and do a live upgrade. My question is whether the regular or live upgrade willdisturb the...

If I run live upgrade to upgrade Solaris 8 to Solaris 9 and have existing ufs filesystem , will I be able to grow the filesystem above 1TB? From what I have read about Solaris 9 you can use newfs -T to prime a filesystem for growth above 1TB but am not sure on an existing filesystem that was...

Is Vault 5.1 software packaged on Netbackup 5.1 CD media? Thanks

Where is the data found for populating the "available disk selections" within the format utility? I am thinking it comes from /dev and /devices after devfsadm is ran. Thanks

what is the correct configuration for the ethernet ports on the SFx800's system controllers so as to connect to network switch? auto negotiate or forced (what speed) full or half duplex? thanks

I get a "not supported msg" when using this command to unconfigure a drive. cfgadm -f -c unconfigure c10::500507630040cb12 configuration operation not supported I didn't stop the NBU's daemons and I am thinking this might be the reason for the message. Does anyone have an input: Thanks

Replaced a bad tape drive and now I cannot get the SG driver to recognize the new tape drive. Solaris /dev/rmt has the new drive cfgadm show the new tape drive configured. running Solaris 8 Netbackup DataCenter 4.5 MP4 L700 with 10 IBM LTO tape drives Added two new drives without any...

Has anyone added a Hitachi 9585 to an existing Hitachi 9900 using MPXIO? If so, how did you configured the scsi_vhci.conf file so that the drives are seen correctly? Thanks

running solaris 8 and getting this error every 5 minutes. ntpdate[214] [ID 398266 daemon.notice] waiting 300 seconds before trying again. Any ideas on why this message is occurring? thanks

Checking to see if any one has seen problems with the IBM GEN 2 drives installed in a L700? Thanks

Have GEN 1 drives install on a L700 Presently the drives have 27Q1 firmware installed. Is there a later version of firmware, also is there a list of problems fixed by firmware updates? Thanks

Solaris 8 password history only support one change. Has anyone used a third party password application which support 10 or more password history depth. I know npasswd is out there and just wondering if anyone is sucessfully running with npasswd or some other third party apps. Thanks

Running SCO 5.0.7 How do you force the network interface to full duplex and have it persistent on reboots. Thanks

Running solaris 8 lpstat shows the print request owner is root login is root When a cancel command is issued for a print request I get a permission denied. Any ideas? Thanks