Search results for query: *

I have a requirement to NAT from 10.0.0.1 to 192.168.0.1. I have a spare Cisco 800 series lying around, which has a built in 4 port switch. The WAN interface is for ADSL, so is not a fast ethernet interface. I am not sure if it's going to be suitable for what I need. I tried this command: ip...

For some reason I was under the impression that on a 5500 switch, only 1 vlan (when in hybrid mode) could be set as untagged. However I see on the 4800 I can have several VLANs untagged. When the switch is on it's own (that is, a single stack, no other switches to connect to), what is the...

Hi, I am trying to configure an ML110 as follows: 1 x 250GB Drive, standalone, OS Disk 2 X 1TB drives, RAID1, Data disk When I enable the SATA mode to RAID and create a logical disk, that all works OK, but when I try to install the OS, the boot controller is seen as the 1TB array and I am...

I have a question regarding VLANs and associated layer 3 interfaces. I have say VLAN10 on a core switch. There are 3 switches connected to this via fibre for edge devices. VLAN10 exists on all switches, and the switch to switch links are set as trunks and allow vlans 1 and 10 (3com switches...

On the 5500G setting up DHCP relay was simply a process of setting a dhcp server and then using almost the same command at the VLAN interface level. This doesn't appear to be the case with the 4800G. I have a single stack with 2 units, currently in use for testing. I have attached one of the...

Does anybody have a sample of a working QoS policy for their Voice VLAN on a 4800G? I have my port set up as follows: interface GigabitEthernet1/0/1 port link-type hybrid port hybrid vlan 7 tagged port hybrid vlan 1 untagged undo voice vlan mode auto voice vlan 7 enable...

I tried this over in the Windows 2008 Server first but was directed here, so apologies for double post for anybody that notices! I've been asked to provide a list of members of a specific group who belong to a particular site. There is 1 OU per site. There is an OU which contains 6 security...

I've been asked to provide a list of members of a specific group who belong to a particular site. There is 1 OU per site. There is an OU which contains 6 security groups. Most users are assigned to at least 1 of these groups. I need to find out people from Site X who belong to each one of...

I'm starting to use the 4800 series more in my job now but previously my knowledge of XRN has applied to 4500 and 5500 switches and it's never caused me any issues. I note that the stack configuration is different on the 4800, but what is strange is that if I try to type anything to do with...

I have installed BIND ON SuSE 11.1 (PPC, on an IBM POWER Server) and in YaST I have an option of DNS Server under network services. I have been through the wizard, configured forwarders etc, but whenever I do nslookup in Windows I get: *** Can't find server name for address 192.168.1.98: Query...

Hello, Is it possible to restrict 5250 (ie telnet) access to an AS400 based on subnet? Eg we have a few subnets: Data - 172.16.1.0 Voice - 172.16.2.0 DMZ - 172.16.254.0 Is it possible to restrict port 23 access to hosts originating on the Data subnet only? If for example a DMZ host was...

To my horror, I have discovered today that lots of our internal Domino NSF databases are actually fully viewable from outside (we use inotes, so if you know the DB name, you can read as much as you like). Clearly, this is a serious security exposure. I know that I can just change the ACL at a...

In our office there are 2 default gateways - one is a leased line which we use mainly for email and website (ie, traffic to our internally hosted website) traffic, the other is via broadband line and is used almost exclusively for staff internet access. Since we installed our x506, all traffic...

Hello, I hope someone can help me with an issue I am having with SSL for iNotes on Domino 8.0.2 In the server document, under Ports > Internet Ports, I have SSL enabled. Currently, Port 80 is not set to redirect. The server has since been restarted. In the Internet Site document for the same...

Hello, I am familiar with installing 64 bit PPC Linux in Logical partitions hosted by i5/OS. I have been told that you can now run 32bit x86 linux by using an emulation mode. I am unable to find very much info on this whatsoever - can anybody shed any light? Many thanks 'When all else...

I have a 3Com access point which can have 4 separate SSID's all isolated from eachother. I would like to make a guest VLAN, but not sure how to block traffic from that VLAN from getting to the rest of the network? Also, if I want to add a DHCP scope specifically for this VLAN, how would I make...

Hello, hope somebody can help. I am trying to make changes to our website, which runs on Portal - however, the web content management seems to be lacking very basic functions such as font type and size and being able to view HTML - there are other buttons such as left and right align, insert...

We had an issue with an 8.0.1 server and have since changed to 8.0.2. However, in the web access tab in the config document for the server on 8.0.1, there was a clear option for wether web access was enabled or disabled however in 8.0.2 I cannot find such an option and we are without web...

Wonder if anybody can help me here? In Outlook, it's possible to have multiple accounts configured, so that when you send mail you get a drop down menu to select who it's sent from. is there an equivalent in Notes? I know I can have access to several mailboxes, but if I send mail from a...

Is this possible in Notes? Sometimes I get multiple meeting invites in a short space of time, and having to go into each one and accept is such a slow process. Is there any way to just accept them all at once? 'When all else fails.......read the manual'