Search results for query: *

Hi All, I have a 2511 and after updating the BootROMs to Version 11.0(10c)XB2, I get the message, "%SYS-4-CONFIG_NEWER: Configurations from version 12.2 may not be correctly understood, and F3: 11943416+616224+825900 at 0x3000060. The router is loaded w/12.2-10b IP Plus. I am assuming...

Hi all, In practicing xmodem on a 2600 router, I changed the console speed to 115000 as was suggested in the Cisco website when running xmodem. I recovered from a deleted IOS, reloaded it, but cannot seem to return the console speed to 9600 from 11500. I get into ROMMON, type confreg...

Hi all, I have successfully repartitioned a 2-partition flash set on a 2500 router to one partition. One flash set was read/write, the other one is a read only and I erased the read/write stick. I am trying to replace the IOS from an IP set to an IP/FW/IPSEC one and need more than an 8 Mb...

Hi all, I have a 2505 I had been using in a lab. I had kept it because it has an IOS Enterprise version on it so it has been useful for practice. Haven't used it lately and when I boot it up, the hub light doesn't come on where the ethernet cable is plugged in. I have enabled the ethernet...

I tried to download Microsoft Live Meeting 2005 before 2007 came out which is not free anymore, but looks like I may have lost my chance. Anyone know where the full install is still available? All I can seem to find is plug-ins. Thanks in advance.

I tried to download Microsoft Live Meeting 2005 before 2007 came out which is not free anymore, but looks like I may have lost my chance. Anyone know where the full install is still available? All I can seem to find is plug-ins. Thanks in advance.

Hi all. Have a strange problem. My 2511 will allow me to make a remote connection via octal cable (reverse telnet) in my lab, but after the connection completes, it bounces my terminal back to User Exec mode on the 2511. In other words it connects to the remote server, but logs me out of the...

Hi all. I have set up a 2500 series router to practice saving/loading images. The workstation IP is 192.168.1.10, the e0 is 192.168.1.11. The subnet mask is 255.255.255.0. The workstation is connected to the router to the e0 interface through a crossover cable and a tranceiver. The e0 interface...

Hi all. I just picked up a 2500 series router. I am trying to reconfigure it for a lab, but before I get an User prompt, the router prints out a line "User Access Verification" and gives a password prompt. I tried resetting the enable secret password, but to no avail, this must be AAA or TACACS...

Hi all. I'm sure this is an easy one but I've got a real good block tonight. Upgraded a 2511's Boot ROMs to Version 11.0 <10c>XB2. Now when I cycle the router I get the following prompt: 2511(boot). (Hostname is 2511). Can't seem to get to a non-boot prompt. I know I have done this before but...

Hello. I am setting up a lab for CCNA and seem to have a problem keeping serial interfaces up. I have started from the setup utility and enabled IP. I have a 1600 connected to a 2500 via a crossover cable. The 1600 is the DCE with a clockrate set. I will post both configs (they are basic) but...

Hi all. We have a 3005 VPN concentrator we cannot VPN into to reconfigure. Just got it off eBay (yes, that could be the problem), so I can't check the IP address either. It boots up okay per the lights. Using Teraterm, w/9600,8,1,hardware, on COM1. Tried Hypertermial also. Cannot get a reaction...

Hi all. I must be a few cups of coffee short today, and must be missing something simple. I am trying to save and change IOS's between 2500 routers. I have done this before without a problem. I have a 2500 connected to a WinNT 4.0 server (with Cisco's tftp server application) via a tranciever...

Hi all, hoping you can help. I have a 2511 I picked up for use in my lab. I am unable to clear the present configuration even after using the "Setup" command. After changing the configuration and saving it, a certain time period passes and if I "sho run", the configuration comes back, printing...

Hello, hoping you can shed some light. I have a 2511 router whose E0 interface will not stay up. I have reset the config, given the interface an IP address and input the "no shutdown" command. However when I exit out of configuarion status and do a "copy run start", upon doing a "sho run" the...