Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
-
PC -> router -> gre tunnel -> internet
Yes.. But my attempt did not work.. I created a route-map that match the host ip (acl) and st the next hop ip to the other side of the tunnel. I also added the host to the nat ACL on the router that I want to NAT the traffic for the host.. The routes are correct (the host can ping the router... -
PC -> router -> gre tunnel -> internet
I want to do the following: (relevant config first) ------------------------------------- router a: fastethernet 0/0 (local) ip address 192.168.0.1 255.255.255.0 ip nat inside fastethernet 0/1 (wan) ip address 213.1.1.2 255.255.255.192 ip nat outside interface Tunnel1 ip address... -
qos on cisco 1800 series and 3g WAN connection (ISP router)
lets say I have the following setup: This is a Cisco 1811 router with 2 FastEthernet router ports and a 8-port switch (layer2) I want the following: traffic from PC 1 should get at least 80% percent of the capacity of the 3g-router when both PC's are downloading. RDP traffic (tcp 3389)... -
90% priority for one vlan
I'm using track rtr and IP sla to set ONE active route I have a cisco 1800 router with 2 non-cisco routers giving "broadband" connection via cellular networks. This is on a ship at sea. So I do not need to know how to route the traffic.. I need to know how to prioritize the traffic All traffic... -
90% priority for one vlan
I already have the routing up and running. I'm using ip sla and track rtr for failover. It is the priority (bandwidth) I'm working on -
90% priority for one vlan
The second router is for failover when/if the first loose the connection. Failover are done via IP SLA monitor and track rtr. -
-
90% priority for one vlan
I have a cisco 1812 router with two routers (internet via two different gprs/edge routers) connected. Both are NAT routers I want to prioritize the traffic to and from one of the two local subnets/vlans local interfaces: interface FastEthernet0/0.2 encapsulation dot1Q 2 ip address 10.0.1.1... -
dual wan with NAT
I do nat see any NAT in those pages.. I already have the ip sla and track part figured out.. -
dual wan with NAT
Can someone provide some example configuration for configuration of a ios router (2600) with 2 wan interfaces (ethernet) and failover for nat? eth0 ip 83.xx.xx.1 / 24 primary wan interface (nat outside) eth1 ip 243.xx.xx.2 / 26 backup/secondary wan interface (nat outside) fastethernet0 ip... -
monitor traffic on catalyst 3550
Ntop have a lot of great features! :) Is there a windows utility to monitor dscp on a interface? I want to monitor number of packets and packet size in different precedenses and queues.. -
monitor traffic on catalyst 3550
thank you very much! I will check out these! -
monitor traffic on catalyst 3550
Is it possible to monitor the type of traffic and dscp for interfaces on Catalyst 3550 switches? Something like netflow on routers... I had a Avaya C460 L3 switch earlier (different company) and used a utility to monitor traffic types and priority.. I think this utility was using SMON to do... -
qos help needed. cisco 3550 switches
We have a network not unlike the one on the picture. It has 3 cisco 3550 switches with 5 subnets (one of them is voice vlan/subnet) One of the switch ports on the 24-port switch is configured as a router port. The fibre gbics "trunks" between the switches. The others are "standard" switchports... -
problem making pptp vpn connection from lan (behind ios router)
I'm having trouble connecting to external pptp vpn servers from my LAN. I'm using a Cisco 2610XM router running IOS adventerprise 12.4.7 I know that the pptp vpn servers is working correctly. I have also tried running access-lists with "permit ip any any" on all interfaces. What can be the... -
cheap or freeware cisco netflow tool
I'm testing ManageEngine Netflow Analyzer 5 now, and that one looks good. But that NetflowTracker was just amazing! I did not find any price for this one.. How much for the full version? thank you -
cheap or freeware cisco netflow tool
is there a free or cheap netflow tool for WINDOWS that shows a "realtime" (max 1-2 min after) statistics from "ip accounting".. So I can have one monitor showing this all the time.. -
NAT causing memory leak
No, I do not have that.. I changed the following line: ip nat pool overload 213.184.1.1 213.184.1.1 prefix-length 24 to ip nat pool overload 213.184.1.1 213.184.1.1 prefix-length 8 maybe that will help. I do not know if this is n important at all, but it make sense.. :) I guess that 48 MB... -
NAT causing memory leak
I added "ip nat translation tcp-timeout 10800" so the NAT entries will not stay for more than 3 hour.. Wonder why the entries are ataying there.... Will the tcp-timeout 10800 command break downloads that lasts more than 3 hours? or will downloads "renew" their nat entries before that? I have... -
NAT causing memory leak
There are a lot of subnets, but not very much traffic/packets.. So I think the router should be more than powerful enough (20-25% cpu usage average during the day)
