Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. soaressteevan

    NEC SV9500 - Cisco SIP Trunk(MG-SIP)

    Thanks for the response. ARTD-CDN 66 is already 15 and ARRC and ARSC is all allowed for the routes.
  2. soaressteevan

    sv9100 outgoing call the number is dial not in service

    same number is working from other extension?
  3. soaressteevan

    Settings Not Saving

    did you try with other browser?
  4. soaressteevan

    NEC SV9500 - Cisco SIP Trunk(MG-SIP)

    Hello, I have configured MG SIP for the SIP trunk between Cisco CM and NEc Sv9500, presenlty i am facing a issue to make an outgoing call from Cisco,which should seize PRI trunk (routeRT120) from NEC(but local calls are going trough Route 21),problem with National calls,which is not going...
  5. soaressteevan

    SV9300 - Station number Display on Idle state

    15210>15> should be 0 or 1 , because in Neax 2000IPS it is vice versa.
  6. soaressteevan

    Phone flashes when call is coming in but won't ring

    Try this:(may be headset from the phone unit is enabled, just disable it) from the unit - Menu - settings - headset - disable
  7. soaressteevan

    SV9300 - Station number Display on Idle state

    sorry for the delay in replying, i have done the above programming, but still i have to lift the handset or press speaker to see the station number.
  8. soaressteevan

    SV9300 - Station number Display on Idle state

    Hello everyone, wants to know which is the command to show extension number on display when the phone is idle. i can see the extension number when i pick up the handset.
  9. soaressteevan

    Night service sl1100

    I think its: speaker 818+1
  10. soaressteevan

    NEC Topaz Auto Attendant Off

    kindly check if the welcome message exists? 1.press speaker 2.Press 716 3.press 5 4.it will ask for the message number(3digit message number) then it will play the message. or may be system is gone to night mode, change it to day mode.
  11. soaressteevan

    sl1000 trunk setting

    command: 1. 14-07 for access map 2, make trunk 2=7(outgoing and incoming) and rest of the trunks make it Zero. 2. 15-06 for station 114 give the access map 2 in all the trunks. in this scenario, 114 will access second line always.
  12. soaressteevan

    sl1000 trunk setting

    command 1. 22-05 for trunk 2 make set the data as 2 in all the modes 2. 22-04 incoming group 2 set the station 114. so you will receive the call for second line in station 114.
  13. soaressteevan

    Polycom IP 7000 with NEC SV8300

    Thank you for sharing this information, its very useful. But here in my scenario, i used meet me conference feature and it worked, every time they make a call they should transfer a call to the meet me conference pilot number. anyway its resolved my issue,thanks for your support.
  14. soaressteevan

    Polycom IP 7000 with NEC SV8300

    Thanks PFD, i also tried the same way, but the customer is not satisfied.
  15. soaressteevan

    Polycom IP 7000 with NEC SV8300

    Mr.Belvedere, they have digital phones, the conference is working fine over there.
  16. soaressteevan

    Polycom IP 7000 with NEC SV8300

    Hello, I have connected a Polycom sound station with SV8300 as a third party SIP, i am not able to make a conference call from this. I am following the below procedure: 1.make a call, once the call is answered 2.press conference button 3.make a new call, once the call is answered 4.press again...
  17. soaressteevan

    Ho do I add end-point licenses to SV8500?

    9801
  18. soaressteevan

    SV8300 incoming SMDR on CCIS for remotre site.

    Yes Belevedere, i can see the station number. 1305 is 0 for all the stations in both the sites. is this feature available on sv8300 on ccis?
  19. soaressteevan

    SV8300 incoming SMDR on CCIS for remotre site.

    Thanks Belvedere, i have done all these programs. my PRI line is in the main site, calls are going via main site from remote site, there is a outgoing call details, even incoming call details are available on smdr tool, but it doesn't give extension number, it gives ccis route and trunk route...
  20. soaressteevan

    SV8300 incoming SMDR on CCIS for remotre site.

    Hello Guys, i have SV8300 systems working on CCIS over IP: Site A is a main office with PRI line connected and Centralized Billing (ma4000) is working. Site B is a remote site . Site B is receiving a call from PRI, but i can not see the incoming calls on the smdr tool, or ma4000. but i can...

Part and Inventory Search

Back
Top