Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. noidatech

    AUDIX Broadcast with Message Waiting Notification

    Hi Experts, We are in need of sending a broadcast message to about 1200 users and we have audix messaging system connected to Avaya G3r using 32 TDM ports. Per Avaya MWI notification should be avoided while using broadcast but i wanted to know if there 32 port connectivity is good enough to...
  2. noidatech

    Getting error while dialing Toll free denial event 1190: No circ/chan

    We have two site SVL and APAC. SVL is having S8710 and APAC is having nortel PBX and Apac is using SVL pbx for dialing out in US via QSIG trunk. Problem is:- When we are dialing 18884444410 from SVL PBX, its working fine. Here is the log. 19:05:39 tone-receiver 03C0006 cid 0x29e6 19:05:39...
  3. noidatech

    SQL query

    Hi all, Im not from DBA background so pls ignore if it seems a stupid question. I am trying to search users from active directory on my cisco callmanger. It doesnt have many search options so i found a workaround where in a AXL API is used to do a query on linux operating system and this sql...
  4. noidatech

    cme & cue

    hi all I am trying to setup a small site with cme and cue in single cisco 3825/3845/2801. The no of users in this branch will be 100 1. Can I use same router for the purpose of cme and cue 2. What is the max no of mailboxes can be supported in cue when used together with cme in single router...
  5. noidatech

    MGCP Gateway registered by PRI ports not

    Thanks, This clarifies my doubt, i read about it somewhere but was not sure. best regards
  6. noidatech

    MGCP Gateway registered by PRI ports not

    Hi, I managed to register my cisco 2801 MGCP gateway in callmanager and but E1 PRI ports are not showing registered when i run sh ccm in cisco 2801 it shows callmanager IP add and status as registered but on the CCM the individual PRI ports are not shwoing registed , instead they show the ip...
  7. noidatech

    Call disconnects when end IP phone is picked up.

    Hi experts, I am bit new to IP telephony world; we have one HKG remote location where the site has ccm 6.0. When we call from US location to HKG site the phone rings and call get disconnected as soon as it is picked up. As per basics it looks codec mismatch issue. Please shed some light where...
  8. noidatech

    BLF not working in 7914 module

    Sorry for the confusion ...7914 module is working fine .user can dial using extension button on it, can even dial speed dial button. Only busy indication feature is not working. When other party picks the call there status indication (BLF button) dose not indicate anything. It remains ideal...
  9. noidatech

    BLF not working in 7914 module

    Recently I have added 7914 expansion module for one user. As per the request I defined the some extensions and BLF-SD button on module. Issue is the BLF – busy lamp is not working, only speed dial is working .Has anyone ever experienced this issue before? Thanks in advance.
  10. noidatech

    Need Help !

    Thanks for the response. AVAYA has its own Intuity voicemail system and call-manager has unity. These are two independent voice system trucked together. User has extension primary 44440 in AVAYA which he has forwarded to CCM extension 56777.People call him on primary extension (forwarded to CCM...
  11. noidatech

    7971 phones touch screen not working

    HI experts , one of our 7971 phones touch screen has stoped working,i did restart but the issue is same.Phone is working fine apart from touch screen issue. Any idea ?
  12. noidatech

    Need Help !

    Hi experts, We have a Qsig trunk between Avaya to Cisco callmanager.when one of my user foward his calls from Avaya extension to call manager extension, the forwarded call dose not go to user’s voice mail. It gives welcome to Cisco unity announcement. When we call direct Cisco phone extension...
  13. noidatech

    third party sip phone in ccm 5.0(polycom)

    im trying to integrate a third party sip phone in ccm 5.0 , its polycom ip station 4000 conf phone anybody has done this before or has some relevent documentation pls share thanks
  14. noidatech

    restricting inbound in CCM from a caller ID

    just wanted to mention that i am using MGCP gateways...and so i am just trying to find a way to restrict them in call manager or on gateways
  15. noidatech

    restricting inbound in CCM from a caller ID

    i wanted to restrict calls from a specific caller ID into call manager, will route pattern or translation help anybody has a good document to start
  16. noidatech

    Phone device load upload in CCM

    anybody has a good document how to upload a new device firmare load in call manager ? thanks in advance
  17. noidatech

    hunt list call coverage

    i watned to acheive so call coverage to multiple extensions ( DNs) just like it works in Avaya. extension A ----3 rings-----Extension B------3 rings-----Extension C----Voice mail of extension A. i know this is possible to achieve using hunt list but can someone explain how exactly it is done...
  18. noidatech

    CCM 5.1 VGA analog , two fax no's on same fax machine

    need to point two Fax DNs on single physical FAX machine, im using VGA 224 with CCM 5.1 can this be done using Hunt Line & Hunt group pointing two DNs to a single DN assigned to single FAX machine
  19. noidatech

    Avaya g3r-CCM 5.1 Q-SIG

    i have gone through various posts on inernet on avaya-cisco q-sig but not much help. anyone running q-sig between ccm 5.1 & avaya G3r need to know if name & number alerting is working on this setup or not if help will be greatly appreciated. thanks in advance
  20. noidatech

    Qsig alerting question

    im not able to see far end PBX extension number when rining, though it sends name ( probably because its configured in DN configuration as alerting name) is this alert number featurer actually supported with Q-sig in ccm 5.1? cant see any parameter on Gw configuration , i heard its controlled...

Part and Inventory Search

Back
Top