Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. curlycord

    call pilot aa

    "Changing the CCR tree on a Call Pilot can be done without disable/re-enable" To a degree this is correct, but only if no callers are on the line listening to AA, so if the site is busy then disable it: If needed, to disable the Tree to make changes in CCR: F983 AA TABLE X (usually 1) Press...
  2. curlycord

    Transfer denied

    A message on the screen ""transfer denied" is when using Norstar External Transfer and not the carriers method, LINK/FLASH. Since it was setup then programming was changed somewhere. External Transfer with Norstar: You are removing Line Pool and External codes and using Dest codes with Routes...
  3. curlycord

    Compact ICS Hidden Reset Button - Solved

    The Callpilot button is on the motherboard, you need to remove the cover to see it. Programming on the CICS is erased: "I then figured it out and found that the button does the exact same thing as the STARTUP process"
  4. curlycord

    Compact ICS Hidden Reset Button - Solved

    I recall this post about the reset button and it looked liked it was never solved in searching the Norstar forum. We would to do the STARTUP (Factory reset) within 15 minutes or powering up CICS, then the secret, wait for "Applying" on the display to show, then wait about 15 seconds, then pull...
  5. curlycord

    Help with Nortel CICS : Do I have CLID?

    No worries, learning experience and/or a refresher for all including me. Interesting, I never knew about 10 channels for AUS.
  6. curlycord

    Help with Nortel CICS : Do I have CLID?

    Yes, plenty of gateways for MICS still. In this case the OP most likely has a CICS.
  7. curlycord

    Help with Nortel CICS : Do I have CLID?

    Are you confusing BCM with Norstar? Norstar only excepts analog nowadays since the other option ISDN/BRI/PRI disappeared. The only possibilities are Modem/Gateway's but it's still analog in the end.
  8. curlycord

    Why is there no thread for Yeastar PBX in the forum?

    "I think there should be a topic for Yeastar PBX systems in the forum" I will assume you meant for "Yeastar to have their own forum". I successfully started the NEC and E-MetroTel forums based on volume of posts related in the General forums at the time/s, but looking at Yeastar there has been...
  9. curlycord

    BCM400 release 4.0 services

    Hi Nikos It does have the sign of a bad hard disk, that when Web related services and CP both stop working because they both rely on the hard drive. Otherwise PS or bad BFT, check for near exploding caps, I think it was green caps were faulty and soon replaced with blue ones.
  10. curlycord

    Page Pac

    As always TTT, thanks for your knowledge and splaining over many years.
  11. curlycord

    Page Pac

    All good points above, I am glad I am not doing paging anymore but I did prefer Bogen. We used to use 1/4 watt setting for most quite applications (office, department stores) and all single home run cables! If I recall, Valcom uses 2 pairs per speaker, power and audio, so an Amp and a separate...
  12. curlycord

    BES50GE - IP Conflict

    One BES50 is looped to the other.
  13. curlycord

    BES50GE - IP Conflict

    Thanks for that refresher/reply. I do not see a way to disable DHCP on these switches so I assumed they do not handle DHCP, instead they rely on the main equipment to handle DHCP. The only DHCP is for the IP address itself, I assigned Static to both but I see that one unit did not take so they...
  14. curlycord

    BES50GE - IP Conflict

    I have an issue with IP Conflict. 'arp -a' shows that both my BES50's (in my own office) are showing 2 IP's each with the same MAC address 192.168.1.226 (via DHCP) 192.168.1.0 My modem is 192.168.1.1 Range is set to 192.168.1.2 - 253 'arp -a' only shows one 192.168.1.0, but I...
  15. curlycord

    Remote changes or support

    Sorry, we vendors, techs and clients do not charge in this forum. The same would be with the other top telecom forum. If you want to help a service company then you need to contact them direct, but in both cases your a little late to the party thanks to "hosted" off site solutions. The Nortel...
  16. curlycord

    Element manager in win11

    That would be nice.
  17. curlycord

    Element manager in win11

    "Is there anyway to use the Element manager in win11 for BCM400?" Only for release 4.0, all previous versions are programmed with web browser only Yes to Win 10 or 11 62.03 was the last regular version, 62.04 and 62.05 were temp fixes for certain issues. Still, you can use anyone. Make sure...
  18. curlycord

    Ring Splash

    Solved! Sets are IP phones and 1 backup digital phone at reception in case of network failure. Mr ramblingrebel went to site and resolved it. The digital phone does have lines assigned as A&R but is set to DND mode until such event occurs. The issue was that somebody mistakenly turned off DND...
  19. curlycord

    Ring Splash

    Check reception set, make sure the Target line/s is told "Appear Only" and not "Appear & Ring" or "Ring Only" It rings the set based on Appear & Ring then CP quickly grabs it hence the ring splash.
  20. curlycord

    call log for Nortel T7316e

    Feature *85 is to only enter/activate or change the password To deactivate the admin does that to protect your phone. It's in Administration programming. Under Passwords/CallLogPasswords/Enter DN/Ext # then press clear. If you are a user then contact your site admin to program as they would...

Part and Inventory Search

Back
Top