Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
-
How to configure a Remote Switch by using SNMP( plz helpppp)
Yep. You can reset the whole config using this method including setting new passwords and login/passwd's on the vty's if you wish. So get the config: snmpset -c <write community string> <switchIP/name> .1.3.6.1.4.1.9.2.1.55.ipaddress.of.tftpserver octetstring <filename on server>" then edit... -
How to configure a Remote Switch by using SNMP( plz helpppp)
You can use my FAQ for snmp passowrd recovery to add login for the vty lines in much the same way. http://www.tek-tips.com/faqs.cfm?fid=862 Hope it helps. If everything is coming your way then you're in the wrong lane. -
Adsl configuration
have you configured your PC with an IP Address, or are you using DHCP? I cannot see any DHCP entries in your config. If everything is coming your way then you're in the wrong lane. -
Cisco Router and only two Ethernet ports
I don't think that will work for your installation... a secondary IP address on an interface or an address on a subinterface will only route traffice on two different IP subnets which exist on the same L2 VLAN. If you have two subnets and two vlans you will either have to use the 802.1q trunking... -
Password recovery on Cat 6509
Ah, you'll find the faq at... http://www.tek-tips.com/faqs.cfm?fid=705 If everything is coming your way then you're in the wrong lane. -
Password recovery on Cat 6509
Take a look at my FAQ, lets you recover the current `config and reset the passwords using SNMP. Good luck, If everything is coming your way then you're in the wrong lane. -
2950 Switches with broadcast storm activity
Have a think about enabling the unidirectional link detection feature on your switches interlink interfaces. In interface config mode: udld enable Unidirectional links are often a cause of relearning MAC addresses. Also, make sure you know the STP configuration of your network. Draw it out... -
Urgent: How to retrieve config without enable password
Read my FAQ to retrieve the config using snmp... http://www.tek-tips.com/faqs.cfm?fid=1160 If everything is coming your way then you're in the wrong lane. -
mrtg cfgmaker $target_name
Hi, cfgmaker is a PERL script which creates the [ROUTERNAME] using the hostname of the device and the interface name. If you pick your way through the script you can change the way cfgmaker creates the name to the way you want it. What is it you are trying to achieve? there may be a much... -
mrtg cfgmaker $target_name
sorry, didn't type that correctly... should read:- cat config.cfg | sed 's/ROUTERNAME/NEWNAME/' > newconfig.cfg If everything is coming your way then you're in the wrong lane. -
mrtg cfgmaker $target_name
You can parse the file and replace each instance of one word with another... e.g. cat config.cfg 's/ROUTERNAME/NEWNAME/' > newconfig.cfg If everything is coming your way then you're in the wrong lane. -
2600 and dialup over ISDN having trouble with understanding dialers
BRI Dial up is usually pretty quick, and wouldn't normally cause FTP timeouts. But if it does then the command you have there "dialer hold-queue 50" (conf'd on the BRI interface) will buffer 50 packets (maximum is 100). You can also specify a timeout (how long it will hold those packets for)... -
forwarding DNS server on 806 router
In order for the router to act as a Proxy DNS, enter the following in global config mode ip dns server then in your dhcp pool, include the option dns-server <ip address of router internal interface> As long as your router is getting the DNS server IP addresses from your ISP, name lookups will... -
Serial connection reset, protocol down?
can you post the output from show int ser 1/0:0 and show controllers ser 1/0 thanks If everything is coming your way then you're in the wrong lane. -
mrtg cfgmaker $target_name
There are options to the cfgmaker command. The one you are interested in (I think) is: cfgmaker --output <mrtg config directory>/<filename>.cfg <hostname> e.g: cfgmaker --output /usr/local/mrtg-2/bin/ABC.cfg ROUTERNAME if thats not what your looking for let me know. If everything is coming... -
2600 and dialup over ISDN having trouble with understanding dialers
Your access lists in this case define what addresses are eligible for NAT. So you can have two identical ACLs one for each dialer. access-list 1 permit 192.168.101.0 0.0.0.255 access-list 2 permit 192.168.101.0 0.0.0.255 and define NAT for each Dialer ip nat inside source list 1 interface... -
Newbie with 2900XL switch
ok, get yourself a TFTP server (there's a decent free one available from 3com called 3CDaemon). And put it on a PC that can be seen from the working switch. Make a not of it's IP Address. Telnet to the working switch and copy the binary to the tftp server. # copy flash:IOSFILENAME.bin tftp if... -
VoIP setupd on Cisco Network
Hi, Are you simply coverging voice and data (VoIP), ie. normally removing wide area voice circuits and piping voice over the data circuits or going the whole IP telephony route, ie. IP telephones on desks? If it's IP Telephony, you have a lot of planning to do! Firstly, I suggest developing a... -
routing to a standby server using Cisco - any ideas ?
You can use Cisco IOS feature SLB (Server Load Balancing) available on Cisco Layer 3 switches and configure it any way you like - Load Balancing / Failover, Hot Standby etc etc - The switch IOS can even check to see if a particular port is available on your app server and make it's decision... -
CISCO 2600 Initial configuration
if "startup-config" doesnt exist in NVRAM you will get the initial config message. simply copying the running-config to startup-config will stop the message appearing. If everything is coming your way then you're in the wrong lane.
