Search results for query: *

Hi All, I have a Cisco 2811 with CCME 4.3 and NIM-CUE module with CUE 3.2. I am trying to connect to the CCME using the CUE wizard and I get "Web Login Failed" and when I bypass the wizard and try and setup through the CUE interface I get "Login Failed - Unable to determine CCM version -1" I...

Make sure you use the T Ports as the other 16 ports are contended at 4 to 1. Not the best for high traffic switch interconnects. 10GB is overkill. do you know what type of traffic you are running over your network? FB

Hi all, I have a a bunch of 5406zl's with the exact same SNMP v2/3 settings. I can manage all devices pefectly from PCM-2.3+ without issue. But, two of the devices have routing and VRRP enabled, and these devices will not send sFlow data to PCM and continuley return "Sampler Owned" when trying...

Sorry, bum steer guys. After looking through the logs it is actually backing up 34GB which to me seems like it is not running compression. The drive is definatley set to run hardware compression. where can I see if compression is being used for each backup?

...and it still gets to this point and wants another tape. - Roughly 19GB All I have done is recreate the job after a stuck job I removed from the *.qsd directory. Anyone seen this before? also, if I am backing up Exch bricks level, do I need to back up the store as well? Anyhelp would be...

Thanks Mark, the emulation of netware is purley astetic as these are very precious users and going from a script that displays progress to a hidden process will freak to many people out and our help desk cant handle it. Cheers Again.

Hi Mark, thnkyou for your reply. I am not really after a progress bar as such, just a window that pops up, displays each drive being mapped etc etc, and then closes when complete- the exact same way a netware script works. Also, the intranet.bat file is for desktop environment confnigurations...

Hi, Newbie here, I need to display the progress of a login script running similar to the way a netware login script runs. I know this is probably basic, I have jsut taken over from the old IT admin and I am totally perplexed. I have pasted in the script I am using. any advice or critique would...

Sorry, I should have stated from the start. This is PIX OS 6.3(4) not 7x, so there is no out statement I beleive. So let me clarify. I have removed my ACL for the inside interface. therefore I should be able to connect to hosts on the DMZ1 network. this does not work. I always understood...

Thanks for your replies guys. Quick question. if I have a rule from inside going out to the ip subnet of my Dmz1 then wouldnt that mean that I can connect to anything on that dmz network from inside and it would maintain the state of the connection therefore I do not require a return rule...

...22.22.22.146 crypto map site-outside 100 set transform-set ESP-DES-MD5 crypto map site-outside interface outside isakmp enable outside isakmp key ******** address 22.22.22.146 netmask 255.255.255.255 no-xauth no-config-mode isakmp key ******** address 22.222.63.129 netmask 255.255.255.255...

Hi, I have a Cisco CSS11503 content switch with 2 Web servers behind it. I currently use IIS logging on both servers and I am seeing in the log the source IP address being the CSS VIP. Both servers and the VIP are on the same subnet with the CSS plugged into the DMZ switch and the two servers...

Thanks for you're reply. Solved it by looking at every device in thier network and found a Catalyst switch undocumented that acted as a distribution switch and when I cleared the ARP cache on this device it worked perfectly. FB.

Hi, I have a bit of a wierd one with a client I am visiting. They have 3 pixs on my internal network. One is the Internet device which is providing NAT for the internal network. the other 2 sit on the internal subnet behind the internet pix. these 2 pixs are protecting another 2 private...

lucky I wasnt confident. no guts no glory, what a load of crap! Ghosting worked perfectly. SMSG. Using Ghost 8.0.xxx, created a bootable Ghost CD witht he Q57 Broadcom drivers. This was for a hardware swap between three servers, 1 being a staging server. I had 2x HP DL380G3's. Both with...

Even though I am pulling out 5x 18Gb's and putting back 4x 36.4GB drives you are saying the raid controller will rebuild the set onto 4 disks? 1 by 1. I'll give it a go, no guts no glory! FB

I had thought of that, but I am not confident as I have to pull out two drives for the first one. (if that makes sense). Actually I have no Idea what would happen. I have moved drives to different controllers (god bless you compaq) but not replaced drives on the fly and rebuild raid sets. I...

Thanks for that. I wasnt aware of any of those fundamental symantec issues. I have successfully ghosted 4x HP/compaq g2 g3's onto various raid sets (hardware) all with 100%success. All 2000 servers, member and standalone. But as you would have read I have never done a domain controller. Thanks...

Howdy, I want to ghost a domain controller to the same hardware, just new drives. I have a Compaq -ML370 G2 with a current Raid 5 set of 6 18.2GB drives. I want to ghost the server then replace the 6 18.2GBs with 4x 36.4GB in a raid set. Controller stays the same, drivers stay the same only...

Solved it. Installed Groupshield.....Only kidding!!. Got all my users to export their mail between the hour that the first corrupt message came into the IMC and bobs your uncle. Pretty big but I didnt really want to use exmerge! FB.