Search results for query: *

We are running SCCP. No Vad within the AS5400. I think that the settings of the input gain and output attenuation may be what we need, but different numbers. Do I need to adjust it according to the ERL? Here are some stats from the sh port voice log. Tx/Rx Power ...

Thank You. We are having this issue on two different phone loads. We have isolated this to the GW. 5.3(0) and 7.2(2.0). What IOS and DSP are you running? What phone version are you using? If I send the same call over SIP or On-Net, I do not have the problem.

I tried to input the settings you noted and it did not make a difference. I also tried preferencing 711ulaw. I already have it set to no vad. Any other suggestions?

Thank you. This you set in your AS5400. We will try this. We have been changing the IOS and DSP etc with no luck. We are using Cisco 7940 and 7960.

Hi, Has anyone ever had an issue with "double talking"? For example, if you call an automated message and try to speak during it, it mutes the automated message until you stop talking. I have disabled vad and also tried disabling echo cancellation. Any suggestions?

Hi, I am looking to replace the caller id name sent from the pstn based on the DNIS. Is this possible and can anyone point me in the right direction? Thanks!

Thank you. I did the factory reset, however, I never was given the option 1 or 2. The phone now will not even give you any options for config etc. Happy New Year!

I performed a factory reset on a 7941 and now it is in a loop from the main screen then to a screen that says it is uploading term41.default and shows the ip address. The term41.default is on the TFTP server. The TFTP is in the DHCP as stated on Cisco. Ethereal traces show it going to random IP...

Check out Geckotech! High uptime, national presence! www.geckotechllc.com

Hi, thank you for your response. My issue is to connect to a new fax server, I either need ISDN-PRI or CAS e&m. I am confused, however that my current tie trunk for a fax server is in mode e&m and the DS1 is set to ISDN-PRI. I did not set the old one up initially. Thank you.

Hi, when creating a fax tie-trunk, should I configure the DS1 Board with CAS or ISDN-PRI? I will be using e&m in the mode for the tie-trunk. Thanks

I have faxes going through my Definity to a tie-trunk and connected to a fax server. I am receiving faxes that are a cut off, but the transmission from the sender says successful. I have tried changing many settings on the fax server with no luck. The problem is that it is random. I do see the...

Hi, I normally don't manage servers and I would like to create a batch file to stop and start two services. Do I just create the file... netstop "service name" netstop "service name" netstart "service name" netstart "service name" Where and how do I make it happen? Thanks

Thanks BuckWeet. I figured it out. I had looked at all the docs and they had an example with VLAN115. Had to put 10 into binary 32 bit and convert to Hex, back to decimal if using the IVR or can put hex in the web interface. Thanks for the help!

That is what I did... with no luck of it working. I have been researching for the past few days. I finally tried it and no IP address. :( Thanks

Is there a way though to force it on the actual ATA? I have done the ways you suggested. I would like to do it on the actual ATA. Thanks

Hi, I am trying to force an ATA to be in VLAN10. I read through the instructions about changing the opflags and the VLANSetting. When I changed it in the web interface, I lost connection and am not able to get an IP address. (Most likely because I entered the wrong values. Does anybody know...

Thank you. I actually figured it out. It was on my side. Have a great day and thanks for the help.

Hi, I have been going back and forth with a vendor about caller id. They claim that I am not sending, however, I see clearly in my Q931 that it is being sent. I have other PRI's that are configured the exact same as this one. This is what their equipent shows. CDN_Digits : 8479548464...

Thanks Orypecos. I actually remembered it. Luckily. Have a Happy New Year!