...it. In 4.0 there is a whole bunch of stuff you can get, but, you need to turn on the trap for the specific events to be published via snmp via the element manager. Lots of stuff on IP, PRI, system state / health, OA&M stuff to!
Feature ** RLS: The feature code to fix annoying phone calls :)
Have you tried to use the i2050 config tool and where it show's the hardware id (MAC address looking thing) click the "auto generate" button a few times to give it a new ID?
Feature ** RLS: The feature code to fix annoying phone calls :)
...to do this from our switch.
Is there a way using CLID routing or somthing like that with routes/destinations so that if a specific CLID rings in I can just sent it to an incorrect destination to achiev the same results as "blocking"
Feature ** RLS: The feature code to fix annoying phone...
Cook1082 is correct.. I learned this lesson the hard way.. It’s got to be SIP to SIP or H323 to H323 to have the 2 BCM talk ”peer-to-peer” without some type of MPCU in between them. VOIP GW Trunk key codes is an H323 protocol.
Feature ** RLS: The feature code to fix annoying phone calls :)
...received from the BCM and then trigger an event, like SEND email… I needed these MiBs on my SolarWinds SNMP monitoring to provide this added PRI down notification, without it, only CPU, Disk, I/O, Ram, Chassis Temp were reported.
Feature ** RLS: The feature code to fix annoying phone...
...pool to use, so I’m still in the situation were voicemail is grabbing a PRI channel and dialing the 4 digit extension of the intended REPLY.. I cannot figure out how to specify use the line pool for the VoIP trunks.. Anyone?
Feature ** RLS: The feature code to fix annoying phone calls :)
...and working.. so I assume there is some place in the Call Pilot i need to program this info.. but for the life of me, cannot find where to do this.
So, can someone point me in the right path?
Thanks and much appreciated!
Jason
Feature ** RLS: The feature code to fix annoying phone calls :)
I had a similar problem using the IE 8 Browser. I used fire fox and it worked.. Chalked it up to a browser problem.. because it was OK before when I did it from IE 6..
Feature ** RLS: The feature code to fix annoying phone calls :)
It's currently NI and Allstream is NI(1) as well.
Options are: NI, DMS100, DMS250, 4ESS, SL-1
Feature ** RLS: The feature code to fix annoying phone calls :)
...drive is dead you should have some alarm lights perhaps on the front panel
You can also open the front panel (grill) and attache a VGA monitor to watch the boot process and see if it booting or throwing a disk error.
Good Luck!
Feature ** RLS: The feature code to fix annoying phone calls :)
Ahh, I understand.
Unfortunately with a shared switch it's all or non on the current hardware you have. Seems like the path of lease resistance is to just remove them name,
Good Luck!
Jason
Feature ** RLS: The feature code to fix annoying phone calls :)
No, there is not.. I've been searching since the Enterprise Edge days and nothing yet... :( (For BCM 400) That I have found..
Feature ** RLS: The feature code to fix annoying phone calls :)
I forgot, I'm on a BCM 400 Rlease 3.6 - This might have changed when they went to Element Manager.. The location to set the business name, that is.
Feature ** RLS: The feature code to fix annoying phone calls :)
...name all together or for the few that need, use the ONN Blocking feature.. but, you'd have to dial it each time prior to calling out.. Kinda like *67 . Not as professional as most might wany.
My 0.02.
Jason
--------------------
Programming Business name display
Programming...
...names)??
I've also (thinking hardware) swapped out the module with another from one of out other offices (Bell's the SP - Name's working) and tested with the same results..
Any insight would be greatly appreciated!
Jason
Feature ** RLS: The feature code to fix annoying phone calls :)
...you know from what version of RCC and were on the PC?
I've looked everywere in the:
C:\Program Files\Nortel Networks\Reporting for Call Center
Directories and cannot find them and there is no start menu
items for this..
Feature ** RLS: The feature code to fix annoying phone support...
...report say "call presented" 104
and "Calls Answered" 112 .. What the difference...?!?
Even if i take away Abandoned (4) from Answered (112)
still don't add up.
Frustratingly so the customer.. and me!
Thanks!
Jason
Feature ** RLS: The feature code to fix annoying phone support...
...my lines are "OK" and
the only reason I see 1-6 and 12-15 is that for this
period of activity, this was the busiest the switch ever
got and only these lines were utilized, thus displayed
in BCM monitor??!?
Thanks!
Jason
Feature ** RLS: The feature code to fix annoying phone support problems!!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.