Search results for query: *

Thanks Whykap. That helps alot. i'm working with my Voip Engineer/Team lead with getting this figured out with our customer.

I've been setting up IP Communicator for many users for my customer. The typical process is the end user would submit a request for IP comm, I would get a work order to set up the profile in Call Manager, and another department would push IP comm to their laptop and it would appear under...

Is there a limit to the number of entries I can have in an IDC table? We may have an additional 1000 digit convertions coming our way and want to be ready. Thanks

I'll have a look at the RDB. Still waiting to hear if the trouble occurs from internal calls from A. ACDN is built in B

a12ozbottle, yes, the phones call call the phone directly.

I've been told that when the phone is forwarded via the FORWARD key (CFXA and CFW 12), the same results occur. As i'm writing this, could this be a problem with the actual cell phone not accepting the call? Perhaps a different CLID/ANI is sent to the cell phone depending on the origin of the...

MWC is set to YES. I did not do the original programming, but I'm helping my co-worker that did. We are assuming that the phone numbers prefix, 800, might be causing the trouble somewhere along the line.

Both sites are set to CFF. From what I understand, the test calls were made from "B". I will try to get an internal call test from "A". Thanks Ace

OK everyone, I have a unique one. Here it goes: Two buildings, two separate PBX's (opt 81s) and voicemails Building A carries all trunking for both; including inbound DID traffic. Building A and B connected via TIE lines. Building B only has a few copper trunks for E911 calls. All inbound and...

Thanks Phonz1. I have already requested the lineup from AT&T. I'll keep y'all posted with the results.

I think I know what you're getting at Phonz1. Call setup and teardown is done by the D-channel. If the D-channel is trying to set up call on certain circuit/channel, and the t1's are not in order, then setup can not occur. Did that make sense? Is that what you mean?

LTM does have all 6 in the route. I forgot to test outbound on the three. I'll test those in a few. I need to set up a test port from Irving to Sacramento and get it done. I'll post outbound test results

TNB FOR ONE OF NEW CIRCUITS: TN 003 01 TYPE DID CDEN SD CUST 0 TRK PRI PDCA 1 PCML MU NCOS 0 RTMB 4 71 B-CHANNEL SIGNALING NITE STRI/STRO OWK OWK AST NO IAPG 0 CLS UNR DTN WTA LPR APN THFD HKD P10 VNL TKID AACR NO DATE 12 DEC 2007 THE REASON FOR TODAYS DATE IS THAT I OUTED AND...

PHONZ1, I didn't think they needed to be in order. This site is in Texas and I'm in Sacramento. I could have my vendor go out and check. I don't understand why my engineer put the three new circuits in the middle.

LD 60: OVL000 >LD 60 DTI000 .STAT PRI* TRK LOOP 2 - ENBL FFMT/LCMT/YALMT: ESF/B8Z/FDL SERVICE RESTORE: YES YEL ALM PROCESS: YES ALARM STATUS : NO ALARM CH 01 - BUSY DID VOD * CH 02 - BUSY DID VOD * CH 03 - BUSY DID VOD *...

...DNUM 9 PORT 0 DES SMART USR PRI DCHL 2 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ESS4 SIDE USR CNEG 1 RLS ID ** RCAP MBGA NO OVLR NO OVLS NO PRI INTERFACE ID 022 2 003 3 021 4 020 5 T200 3 T203 10 N200 3 N201 260 K 7 BKUP...

Johnpoole, I just tried your script and it worked fantastic. I do have an ignorant question, though. My company has PBX's in every time zone. If I'm on the west coast, and run your script while logged into one or our east coast PBXs, will I've just set it the pacific time? Thanks

It Works now thanks to dlesap and his suggestion to look at LD 16 RDB,DNAM YES. DNAM defualt=NO, Changed it to YES and it worked fine. I have several very happy call center managers. Thanks to all that replied.

Here's the scenario: 800 Call is presented to PBX via T-1 DNIS (1532) digits are received DNIS (1532) converted to 5032 via IDC table 5032 is an ACDN that is NCFW to Voicemail In Meridian Mail: 5032 is a TD controller Caller is given menu options Option 2 is to be transferred (Call) DN 6132 DN...

AceWarlock: No. it is not.