Search results for query: *

is the same using the 8 ACOD or dialing just the cdp

acewarlock this is the TN TN 002 0 00 01 TYPE 3903 CDEN 8D CUST 0 FDN 7990 TGAR 1 LDN NO NCOS 4 SGRP 0 RNPG 0 SCI 0 SSU 0080 LNRS 16 XLST SCPW 1234 SFLT NO CAC_MFC 0 CLS TLD FBD WTA LPR MTD FNA HTA ADD HFA GRLD CRPD STSD MWA LMPN RMMD SMWD AAD IMD XHA IRA NID OLD VCE DRG1 POD...

yes i can i see the names and also i have callpilot with NMS working fine

and this is the CFN DES CALLPILOT N1 512 ADAN DCH 11 CTYP MSDL CARD 01 PORT 1 DES JILO USR PRI DCHL 1 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ISGF PINX_CUST 0 ISDN_MCNT 300 CLID OPT0 CO_TYPE STD SIDE NET CNEG 1 RLS ID 4 QCHID YES...

...NO DNIS NO DCDR NO ICOG IAO SRCH RRB TRMB YES STEP ACOD 8 TCPP NO TARG CLEN 1 BILN YES BLEN 10 BNUM 0000000000 BDSP YES OABS INST IDC NO DCNO 0 * NDNO 0 DEXT NO ANTK SIGO STD MFC NO ICIS YES OGIS YES PTUT 0 TIMR ICF 512 OGF 512 EOD 13952 PAGE 002 NRD 10112 DDL 70...

well is Nortel to Cisco - Cisco to Nortel using this DCH DAN DCH 11 CTYP MSDL CARD 01 PORT 1 DES JILO USR PRI DCHL 1 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ISGF PINX_CUST 0 ISDN_MCNT 300 CLID OPT0 CO_TYPE STD SIDE NET CNEG 1 RLS ID 4...

the 8 digit is the ACOD and 4460 the ext. also i have CDP with 44 but is the same goes busy i mean forwarding 84460 and 4460

thanks acewarlock i have two Op.11 using PRI with QSIG when i try to forward to the other system goes busy this is the TN TN 002 0 00 01 TYPE 3903 CDEN 8D CUST 0 FDN 7990 TGAR 1 LDN NO NCOS 4 SGRP 0 RNPG 0 SCI 0 SSU 0080 LNRS 16 XLST SCPW 1234 SFLT NO CAC_MFC 0 CLS TLD FBD WTA LPR MTD...

call forward using PRI is not working any idea ? thanks

many many thanks to all for answare thanks

hello someone has the list of all the patch and what is the meaning of each patch patch from 22.08 till 5.0 thanks

display your partition table

Johnpool as comment the people of this system has accustomed as SCR you know i mean, ringing all the MCR at the same time

...ISS1:1OF1 p24005_1 19/09/07 p24005_1.ssc NO 159 Q01649622 ISS1:1OF1 p24012_1 19/09/07 p24012_1.ssc NO 160 Q01196513 p21015 p24215_1 19/09/07 p24215_1.ssc NO 161 Q00957691 ISS2:1OF1 p22644_2 19/09/07 p22644_2.ssc NO .**** >

only one think i have SCR on all the 3903 and 3904 sets but if a set MCR works fine but it was working as SCR 3 months ago the 4.5 as an DEPLIST with 121 patch on september i install the last DEPLIST with 161 patch i guess was the new DEPLIST, but i dont know which one is the mising patch...

hello i have to Op11 connected with a cisco using PRI2 and QSIG one is 4.5 and the other is 4.0 but only when the primary DN is busy the second call not work (only in PRI calls) and this the error that the MSGI and MSGO send DCH 11 UIPE_IMSG CC_DISC_IND REF 00007928 CH 1 1 TOD 18:12:28...

first thanks to all for help on this and i had to change the SSC Card to fix the problem again thanks

thattekguy the system has 3 years installed with the same tty config but i gone try erasing the CTY on TTY 1 thanks

yes i did yesterday and is the same i only have access one time either reboot or shutdown the second time i go back to the same all the TTY do not respond

...#01 LOGGED IN ALADMIN2 20:16 11/10/2007 >ld 37 IOD000 .stat tty TTY 0 : ENBL TTY 1 : ENBL DES: MODEM TTY 2 : ENBL DES: cdr TTY 8 : DSBL .**** OVL000 >ld 22 PT2000 MARP NOT ACTIVATED REQ prt TYPE adan tty ADAN TTY 0 TTY_TYPE SDI CAB 00 CARD 00 PORT 0 DES FLOW NO...