Search results for query: *

Nothing above stated, I am in this case in a position smart hand. Remote maitainer sent me to site reset the card if no succes, then replace with the new card, because they have such a problem with card, that card is workin, but Card can not see in the G450 ...

Thank you gentlemen! Sorry about that multiple querying, I was a bit scatterbrained :)

with that "busy" you meant any command, something similarly as in the Nortel PBX,LD60 DISL?. LD96 DIS DCH ...?

Hi, I want to replace the defective DS1 boards from the G450. Can I please simple only pull the MM710 card out, without disabling the card and than replacing with new DS1 card? If not, could anyone write down Replacement procedure the defective MM710 card from G450? Thank you in advance

Hi, I want to replace the defective DS1 boards from the G450. Can I please simple only pull the MM710 card out, without disabling the card and than replacing with new DS1 card? If not, could anyone write down Replacement procedure the defective MM710 card from G450? Thank you in advance

Hi, I have experience with Nortel systems but very small experience with AVAYA G450. I must replace the defect MM710 E1 card on G450 to new card! Is this card hotplug or must be first disabled? Excuse me, maybe a stupid question .... Could someone please write me step by step, how to replace...

Hi Splic3d, thanks for the reply, I also have document, but I´m looking for download a msi file.

Hi, we have issue, cannot launch Real-time displays by AACC,in the documentation is written as follow :To download the RTDControl, you can download the control manually or you can download the Multicast Trace Tool.msi on the client PC. Can anyone advise us where we can downloading:"Multicast...

Hi, we have issue, cannot launch Real-time displays by AACC,in the documentation is written as follow :To download the RTDControl, you can download the control manually or you can download the Multicast Trace Tool.msi on the client PC. Can anyone advise us where we can downloudig:"Multicast...

PNI setting is the same at all nodes, major issue is NMS package 175 is missing in one of these PBX. Thanx guys :)

thank for help, unfortunately only one of them PBX got NMS package 175 enabled [mad]

Hi have someone experiences how to configure Nortel PBX for the "transfer" of MWI information (Message Waiting Indicator) messages between two PBX´s? we have 2x small PBX´s interconnected via PRI-TIE using MCDN protokol. (PBX1=Nortel Rel5,5 & PBX2= Nortel Rel4,5) What should I need set at...

• for the NT5D97AD DPRI card, the following cables are used: - NTCK45AA 120 Ohm Dual PRI to I/O Panel cable (8ft) - NTCK79AA 75 Ohm Dual PRI Coax Cable (40ft) - NT8D7217 Dual PRI I/O Panel to Multiplexer cable (50ft) Integrated Digital Access (IDA) equipment 76 DASS2 Fundamentals November 2010 -...

Hi we changed our Trunk connection to PSTN from DTI to PRI. But now we have problem,with many sleep errors, we miss special cable NTCK47 or NTCK81.. Does anyone know the pinout for NTCK47 or NTCK81? The best solution would be an "self made" cables. Thanks

Hi how can I change default Administration Password (COLOR*SET)? Thanks

Hi Tman45, thaks for update, my CS1000E PBX consist only from two chassis. IPMG[0-0] has CP-MGS Card and IPMG[0-1] has MGC Card. ELAN is completely abandoned, it consists only from one patch cord pulled from CP-MGS card to port E1 on MGC. Today I uploaded the new LW for DSP, we'll see what it...

Hello, I have some problem after UPG OPT11MINI R4.5 to CS1000E to Rel7. IPMG 0-1 randomly lose ELAN connectivity to the CPU ??? Last Time problem repeated 4 time over about 50 minutes, see file below. But ELAN is taking a direct cable connection between IPMG and CP-MCS.I have repalced (before...

Hi all could anyone experienced help me please ? Our CS1000 after upgrade to rel.7 has some problems, for example-randomly short interrupted the ELAN between the CPU and on-board MGC card or DECT phones randomly stops working, only restart DMC card is helpful. Paches are up to date ... I decide...

hi rogercentella, what you mean with "The solution we found was to update the GPS"?

Hi, after upgrading to Rel.7 system approximately every 20-30 seconds to generate reports below: --------------------------------- ipcrm starting: sipProcsd using uid:500 gid:500 for startup. cat: /var/run/sps/sipProcsd.pid: No such file or directory /opt/nortel/sps/bin/sipProcsd Initiating...