Search results for query: *

Most of the time it is just Straight Cat5/6 Cable, same pinouts on both ends.

Well, based on the information I can only guess. - do we need additional hardware to support this? I'm thinking I might need a WIC-2T as well? Or something else? Most likely yes, you will need 3 T1 ports, if you only have one, you will need a card with 2 additional T1 ports that is compatible...

Can you post the output from the following commands on your 2911? Show version Show config

You can connect your internet connection directly into ASA5510 and then plug the 1841 to one of the Inside interfaces. What do you need DMZ for?

Can you post rest of your configuration from the ASA?

How much VA is required for the backup power supply?

TTL is dependent on the host you are pinging, and has nothing to do with the Medium (VPN in your case). Differnet machines have different TTLs, for example new Microsoft machines have TTL 128, routers normally have 254, old machines have 32 and so on. You can check TTL of your local machine by...

I was afraid of that. Thank you for clearing it up.

That was it, I took them out of AA # 2 and everything is now working. Thank you so much for your help, I spend few hours going through Release 7 Manual which is over 1000 pages but fairly useless you already know how to program the system which kind of defeats the purpose. I have attempted to...

I have setup an extension for Remote Call Forwarding. The user dials #3391<cell#> from his phone set in the office and it works. The issue is that if there is a power failure and System is reset, the forwarding doesn't work anymore. Someone has to go to the extension and redo the forwarding. Is...

Thanks Tom. It worked to a certain extent. We do not have delay, and Auto Attendent picks up the calls. The other Lines/Pools were assiged to 770, and I added Group 894 in there too. Now the calls are no longer going to Operator but are picked up the Auto Attendent. There is one issue though. I...

I already had three pools of incomming and trunk lines 70, 890 and 895 which are working fine. I added a new pool 894, but incomming calls on the lines assigned to pool 894 ring on the Operator's Desk instead of being picked up the Automated Attendant. Am I missing anything?

It does. Let me researh further see if i can make it work.

SCO OpenServer Release 5.0.4 VMWARE SERVER 1.0 | 7/10/06 | Build 28343 Anything I can try? /dev/install, does it refer to floppy disk, cdrom or hard drive?

When I try to install SCO on VMWARE, I get an error message Error initializing /dev/install ? Can someone help me?

Got you. I think I will be able to do that. Thank you very much ttech, merlinman and eveyone else for your help and time.

That did the trick, it is working now. One last thing; is there a way that I can restrict outcalling to a certain are code only (using allowed, disallowed lists). I have tested by appling disallowed list number 7, and this prevents calls to 0, 011 numbers etc. List : 7 Entry 0: 0...

Please let me know if this is what you were looking for: EXTENSION INFORMATION Extn SS/PP Type 195 8/ 6 T/R CTI Link : No Alarms: ACTIVE Pool Access : Page Group : Primary Coverage : Secondary Coverage : Coverage...

There is not port on the 007 MLM Card to plug single line phone. It has only lights for VM1 through VM6, so please guide me how can I test or monitor the port. Yes, I can call the cell phone by dialing the number through any extension. Please guide me how to monitor with the test set. In the...

I have removed extension 195 from the dis-allowed list, didn't work. I also tried to creat an 'allowed' list with first 6 digits. No luck. I have also tried with and without 9, (we use 9 for all outbout calls), didn't work. Am I missing someting? I have access to SPM in case anyone would like to...