Search results for query: *

Many thanks for your advice, I'll give it a go and see what happens. Thanks Rob

Hi Burt It's an internal link and BT haven't provided any IP info, so I was going to use a private class C with 30 bit mask. Thanks Rob

Hi I'm looking to configure 2x 2811 Cisco routers, connected by a BT 10mb national ethernet. As the 2811's have two ethernet ports, the plan was to connect one port to the internal network and one to the BT demarc at each site. My question is, does the ethernet ports I'm using for the WAN...

Thank's for the advice, looks like a good reason to upgrade to win2k. One last question though, how do your client PCs get a DHCP address from the server? DHCP relay on the router ? Thanks again Rob

Hi Does anybody know if it's possible to join / authenticate to a remote domain on a different subnet. I currently have my PDC on one site and client PC on another. There currently connected via a bridge (single subnet) and it all works fine (if a little slow). I’m looking at upgrading the...

I have had a HP StorageWorks NAS 1200S dumped on me to be used for file storage. The unit has Windows Storage Server 2003 installed on it. The question I have is how is this operating system licensed? Can I just attach as many clients as want to this device or do I need to purchase...

After reading this thread, it seems apparent that I am having a similar sort of problem. I have had a HP StorageWorks NAS 1200S dumped on me to be used for file storage. The unit has Windows Storage Server 2003 installed on it. The question I have is how is this operating system licensed...

Thanks for all your replies; I'll research your suggestions and let you know how I get on. Thanks again Rob

Thank you all for your responses bell1996 This is more or less what I have at the moment. Because of the admin overhead of 2 default gateways I'm looking at somehow creating 1) One gateway 2) Maximum bandwidth to remote site 3) Hardware and connectivity failover All kit used is Cisco 2620 If...

Hi Has anyone got any suggestions of how I can load balance between two separate routers that are going to the same location. There currently set up for fault tolerance using EIGRP, but this creates a problem of two default gateways. I'd like to have one default gateway that routes data to the...

Hello all Wondered if someone could help. I'm trying to Nat all inside traffic out via atm card ip address, which seems to work fine. The problem I've got is allowing external traffic inbound on port 8080. I've added what I think to be the command but it dosn't seem to work. I think my problem...

Hello all Is there such a thing as default ACLs ? i.e. If I didn't specify any ACL in the config, what protocols and ports would be permitted and denied on each interface. Thanks for any help Rob

This is just what I was looking for. Thanks again for the help. Rob

Hi I've got a Cisco 2600 directly connected to the internet via DSL card. I'm concerned that it may be open to attack. Could anyone please suggest any access-lists and protocols to deny. I only want web pages to pass through. Thanks for the help. Rob

Does anyone know of any software that can generate ios commands from graphical interface, simlar to config maker. I've got ver 2.6 of config maker but it dosn't support my hardware and IOS. Thanks Rob

Hello all I'm tring to set up 2 x 2600 routers to bridge over ISDN. Could anyone please spare the time to have a look at my config. I've tried using some debug commands and the lines are active but never placed a call. Thanks Rob *********************************************************...

Hello I wondered if anyone out there has any example ISDN bridge config I could have a look at. Using 2x 2600 with 4x bri. Any help would be great. Thanks Rob

Please Help Is there any way of removing config other than the "no" command, And is there any way of doing a factory reset? Thanks for the help Rob

Please Help I have deleted the image file from the flash card of a 2600 router.Consiquently when I relaoded, it just came up with the rommon prompt. Although I have the Cisco CD with software on it, it only contains .bin files. How do I convert or get hold of an image file. Thanks Rob