Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations gmmastros on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. donbru01

    3COM NBX (V3000) gets hung!

    Press any key to stop auto-boot... 7 6 a questo punto digitare un qualsiasi tasto per bloccare il boot [VxWorks Boot]: ? digitare ? per vedere il menù possibile ? - print this list @ - boot (load and go) p - print boot...
  2. donbru01

    3COM NBX (V3000) gets hung!

    Try to stop boot , configure NBX to start with previous release
  3. donbru01

    3Com NBX SIP Connection To Another PBX?

    Yes , no NBX100 only V3000 or V5000 need upgrade memory Bruno
  4. donbru01

    V3000 Patches

    send me link how i can put patch by bruno
  5. donbru01

    Add third party device

    no only user and telephone group how 3 party sip phone . You must go on sip phone and configure - sip server your ip nbx - sip outbound proxy your ip nbx - user-id = your extension create in nbx - autenthication is = your extension create in nbx - password = default password if i remember...
  6. donbru01

    Add third party device

    simply , you ust create only a user example extension 2000 you must configure device using user 2000 password 1234 ( or psw voicemail ) , important timer expiry 3600sec
  7. donbru01

    phone licenses

    try this link http://www.nbxhelpdesk.com/main/
  8. donbru01

    Add third party device

    sorry you have enable nbx to sip ? had you ram necessary ? what nbx is ( 100 no sip enabled , v3000 , v3001 or v5000) what type third party you installed?
  9. donbru01

    request

    Sorry , have you also manual of hardware installation ? No software configuration i have it thanx Bruno
  10. donbru01

    request

    thanx soo much at all . bruno
  11. donbru01

    request

    Hi at all , i need software for configuration ipldk 300 . Anyone can send me software ? thanx
  12. donbru01

    3COM licensing

    http://www.nbxhelpdesk.com/main/
  13. donbru01

    Prompt Missing?

    go into Autoattendant / select menu that is deactive and press active
  14. donbru01

    M Line

    ok thanx below e2tshow -> e2tshow e2tshow Found an E2tProxySp. Will run e2tproxyShow as well -------------------------------- E2tProxySp Status -------------------- Local E2T has 64 Audio ports, and 128 T38 E2T Listening ports. Is Connected to E2tProxySp. Uses direct transcoding. E2T...
  15. donbru01

    M Line

    Hi Irwin , thanx soo much yes now i can connected on RTC via putty . But i have found new possible cause for my problem Duplicate IP Address , how i can verify what IP Address is assign on E2T? Log Number: 4950 Severity: Error Date: 2012/Nov/22 Time: 09:32:09 Source...
  16. donbru01

    M Line

    HI Irwin , i am try to connect via via putty but Mitel refuse connection i must use different port ? You are very expert to Mitel ,can you say me from logs below if TDM,PortID:13 is channel 13 of my ISDN PRI ? 1064 Date: 2012/Nov/23 Time: 10:51:26 Source: CCC_Ipsw Description...
  17. donbru01

    M Line

    hi yes issue is when from cucm make blind transfer to mitel but i need make sometime this tranfer and i found command for restart e2t w/o restart call server when issue occur sorry from command maintenance i cannot make e2tshow , i must connect via consolle cable?
  18. donbru01

    M Line

    Hi Irwin , about your question i have this HW Resource on my Mitel 3300 MXe T1/E1 w/dual inband loopback quad Bri(S/T) Quad BRI(s/t) 4 sharc 21161 dsp embedded echo cancellation 64 channel Where is E2T ? there are a chance to reboot this E2T? thanx
  19. donbru01

    Minimum Software Release for to Send Outbound Caller ID, NBX100

    NO problem all software send correct outbound caller id via pretranslator You have problem with pstn / isdn E1-BRi / isdn-T1??
  20. donbru01

    M Line

    Hi at all , confirm all issue incoming when CIsco CUCM via trunk sip make a blind transfert to Mitel . Today i have allow this feature after 3h more logs with error

Part and Inventory Search

Back
Top