Search results for query: *

HI Guys we are moving off of our NEC r11 2400. Short story - telco goofed the port and I have 200 numbers I have to call forward morning of cut. I know historically that the MAT software will not allow a way to paste numbers into the CFD window. Is there a hack or way around that? Looking to...

Thanks guys! The SPST command works great! Have not seen you all for a long time. We are in the migration to a Cisco CUCM sand I keep our NEC running with duct tape and ebay parts. Damn thing has been pretty solid with exception of ATT's wonderful crumbling copper t-1 service. I will soon have...

this was great. never knew about this command. Star for you

trying to locate a command that will list stations or lens in make busy status.

Hi everyone, new to Cisco CUCM. we are in process of design for users. I have some q's I am an old NEC / Avaya tech. Looking for CUCM feature that is equivalent to call fwd Im here or Follow me / hoteling for internal extensions. I looked at extension mobility and that is great BUT we are...

Yes we have fully redundant. Switched over TSW, no change. Will reset the Adtran Atlas 800 after looking back and seeing other DRU errors/failures/ warnings as well. Good call.

Hi all, Still running my NEC legacy system. One of my sites is having framing slips on its PRI (24PRTB-a). Telco swears it is a PBX issue and not their problem. It has been running great with no issues until two weeks back. I have checked jumper for clock and no changes have been made in system...

is it possible to install an ATTCON?

Hi GUys, A real oldie here. 2400IMX R-11. Is there a command to list up all stations busied out with MBST? I have 3 2400's I need to look at.

transfer added the pause which was perfect. Thanks

Been awhile, I have a 2000IPS connected CCIS to a 2400. The voice mail pilot on the 2400 is 2400. On the IPS I am trying to set a speed dial for 2,400 but for the life of me cant remember how to enter the comma. Any ideas?

This is it! I think there was a shorter way onle in the cmd shell but this works regardless. THANK YOU

I have an OpenText Gateway 2100. I had instructions on how to check if my PRI T1 was slipping/errors but have misplaced. Can anyone point me in the right direction?

HI ASll, I am trying to set call block on my 2400IMX r11. I can get the block to work with ACID BUT it only transfers to voice mail and I would like the blocked call to go to busy signal. Can any7one shine some light on this?

Unable to run MEM_HDD while on CPU 0. I am thinking the flash card is shot. Any ideas? Can I swap the flash cards and see if trouble follows? Is the flash card replaceable and wold I have to format?

what pim and slot does the LCB card reside in. I have an IMX as well

HI Guys, Been a long time as my network eng duties have pulled me away from my PBX work. Trying to find a way to get a daily route peg count for our 3 Fusion 2400's and 3 CCIS 2000 systems. I am hoping someone knows how to set this up for daily peg counts so we can determine call volume inbound...

Any Rightfax pro's here? I have Rightfax with Opentext 2100 gateway. We are experiencing very slow recieve and transmit. Also unable to fax more than 5-6 pages. Any ideas???

Been awhile since I have been here. Does anyone know how to set Call ID blocking on 2000IPS? I have searched through Feat & Specs and am not having any luck. I found call redirect but no blocking.

Thanks for the quick responses! I opted for the dtr model . Sorry for missing your request troll. My network duties have overshadowed my PBX passion. Just off the top of my head I don’t think the IMX uses dongle that used on previous ICS. Someone please correct me if I am wrong