Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations gmmastros on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. wonga316

    BCM Rebuild

    Thx for the quick reply Naurry. I managed to located the doco for BIT. The instructions make reference to BIT CD and BCM image CD. Do these CDs come with the BCM from the factory? The BCM in question is at a remote site so I'm unable to check. And a access code to allow the imaging to proceed...
  2. wonga316

    BCM Rebuild

    Does any one know where i can obtain the documentation for the a BCM software rebuild? No one knows administrator account to get into NT and UM. Nortel have recommended a re-install. I have searched my documentation but they only state how to configure the BCM straight from the box. I want to...
  3. wonga316

    Time to jump into BCM? Newbie planning...

    I have never purchased nortel gear from non-nortel certified suppliers. From my experience unless you have signed a support agreement with a nortel partner it's very difficult to get related doco or patches. I do know occasionally nortel do have promotional sales where they chuck in a few extra...
  4. wonga316

    Media Bay Module Type

    I have 2 CTCM modules on bus 3 and another 2 CTCM modules on bus 4. Bus 3 and 4 have been setup as trunk modules. so they look like CTM4 MBM bus03 module03 module type - loop module mode - gloabl # of lines/loops 4 bus03 module04 module type - loop module mode - global # of lines/loops 4...
  5. wonga316

    Media Bay Module Type

    Thx biv434. But i have another silly question. I have a BCM200 and the 2 MBM have a CTCM installed, yet i can see T316E digital handsets programed on the BCM. How is this possible if all the MBM are occupied and they are analogue trunks?
  6. wonga316

    Media Bay Module Type

    Has anyone seen a MBM type CTCM? I was wondering what it does? I have a number of BCMs that show this type of MBM when i do a inventory print from the maintenance section of UM
  7. wonga316

    BCM System Time "Slipping"

    I have BCM200 running 3.6 version 2.2c. Occasionally the system clock "looses" a minute here and there. Eventually the system time on the BCM appears to be 5 to 10 minutes behind the current time. I'm able to manually change the system clock but i was wondering if this is a known issue with...
  8. wonga316

    BCM VLAN Voice and Data

    Hi, We have a BCM which we access remotely via LAN1 over a network. Its it possible to VLAN LAN1 so the VOIP and data traffic are segerated. I have found the section in unified manger where you can add additional IP addresses and some documentation on VLAN setup with IP handsets. So i just want...
  9. wonga316

    BCM CDR Error - Can't Change to Working Dir

    Thx biv343. Could it be anything else if the 3.5 system. To be exact it's a BCM200 running 3.5 version 2.3b
  10. wonga316

    BCM CDR Error - Can't Change to Working Dir

    hi, i have a number of bcms where i have managed to sucessful setup an ftp push on all them except for two. they are running 3.5 and 3.6. an attempt gets the following error can't change to working dir = 5!!! i have check the e:\ and there is over 1gb of space on both. a restart on both...
  11. wonga316

    How to check and change SNMP Community string for M1 11cmini, 11c, 61c

    we are having a similar issue. i have checked the NTP and confirmed that the required pkgs are installed on the meridian 1. we are running release 3 but all of the commands related to SNMP chg and prt in LD117 are not recognised by the system.
  12. wonga316

    meridian 1 SNMP traps

    hi, i have been able to sucessful setup snmp / open alarms on our multiple meridian 1. i was wondering if it's possible to allow major and critical alerts to be sent to our snmp trap server instead of just one or the other? currently, i have set suppress_alarm to 2 for major. i have found that...
  13. wonga316

    OTM D-Channel Reports

    I have scheduled an hourly traffic collection on a number of meridian system with OTM 2.2. When i attempt to run a D-Channel report to see the incoming and outgoing calls i get 0 enteries for all fields. thanks
  14. wonga316

    Default Next Hop Router Changes Via Putty

    I have a number of BCM's where i have to change the Default Next Hop Router. if do this via puTTY interface do i have to restart the system? i have also read in the NTP that ip configuration will erase programming. is this true? normally i would make the change this via unified manager but...
  15. wonga316

    Unified Manager unable to load java applets

    when i attempt to open 'configure' on the bcm unified manager the java applet fails to load. other sections of unified manager are functional and i have java web start installed on my client machine. refreshing doesn't seem to work.
  16. wonga316

    OTM - Adding site via ethernet option

    thx mlukie1. silly question, when you refer to the 'switch' is that the CLAN or the PABX itself?
  17. wonga316

    OTM - Adding site via ethernet option

    i'm attempting to add/connect to multiple sites via OTM with the ethernet option (11c - 61c). how do i find the ip address of the system. i've had a look in LD 117 but i think that it is just the ELAN.
  18. wonga316

    Server's ID has not been certified

    new to dom and .doc. have recently installed R5 on ms svr 2003 standard edition. install was setup as new svr. when i attempt to connect via dom administrator (installed on another machine) i get the following error - "the server's ID has not been certified by a certifier that you trust." i can...

Part and Inventory Search

Back
Top