×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Contact US

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here
Home > Forums > Wiring Closet > Phone and Telephony Systems >

Nortel: Norstar systems Forum
Advanced Search

52 records matched your query of E&M outbound. Outputting records 1 to 20.

Keyword(s):
More Search Options
BagsNYC (Vendor)
... and as outbound dialtone. I was told E&M trunks were the way to go..Is that not the case?...
...I am trying to find out how a inbound E&M trunk is provided from telco via copper. Is there 8 wires...
stillabdul (IS/IT--Management)
... provider and use either E&M trunking or ISDN-PRI as both support inbound DID and outbound calling...
...Make your line type E&M on the lines you want to go out on so that you can use them both directions...
NSupporttech (Programmer)
...If you program your E&M for Auto Answer then you can use them for inbound and outbound...
..."If you program your E&M for Auto Answer then you can use them for inbound and outbound...
lgross (TechnicalUser)
... are loopstart, groundstart, DID and E&M....
...I'm not familiar with the BCM, but on a Norstar you can set up a T1 as E&M, assign the trunks to a...
DOcean (Programmer)
... for an MICS with T1/PRI? Loop Start, Ground Start, Wink Start or E&M Wink Start... ??? ...
...If you want to treat it like a 2 way DID I would go with E&M, WNK Start, with Auto Answer Trunks....
JeffSlone (TechnicalUser)
...Setup: I'm coming into a system via an E&M card and hitting the DISA DN, I have a COS password set...
...; L068 is the last line in Pool A, which is the PRI-A; Lines 001-024 is E&M (pool G) Lines 25-47 is PRI...
sohtnax (IS/IT--Management)
...From the installer guide: "Alarm: 63-Z 1. Check that you have the required E&M Trunk...
... mode is correct for all the loop start lines. 3. Make sure that all of your E&M trunks installed in a...
KrisBoutilier (IS/IT--Management)
... is running as 24 E&M wink tie lines to another pbx, the KSU is driving 64 stations and the system was cold...
... cartridge." So with 24 E&M trunks on a RBS T1 (all Auto Answer) you're limited to 4 concurrent call...
jsaad (IS/IT--Management)
...I have a customer not willing to part with their MICS 3.0XC. I want to put in a T1 E&M card...
.... This condition was seen only on systems that used TI E&M auto answer trunks with high traffic. In this scenario...
... LINE CODING: B8ZS CLOCKSRC: SECONDARY LINES: E&M POOL: A Supervised Also, I read a post...
... that asked about whether the lines were set to ground or loop start. Doesn't the E&M (PRI T1)setting replace...
bwtc (Programmer)
... Cisco IAD, which plugs into a T1 card (E&M) on the MICS. Yes, I do hear the fax machines trying...
...Phoneguy, I'll try the f#808, but how will the "Long Tones" help? On outbound faxes, the fax...
tkoon (IS/IT--Management)
... comments) is this correct? or do you have E&M trunks that the telco is outpulsing to you...
... that was done on this was lines 025-048 setup for E&M pool b Pool A contains all the copper lines. When...
capcoms (Vendor)
... expansion (not combo), services card. The T1 is set to ESF, E&M wink, 21 channels with DID service...
.... [color red]Could it be that my E&M channels 17,18 19,20 and 21 are receiving inbound calls after...
DTone (Vendor)
... will need to tell Telco which channels you want to designate E&M tie circuits. To Disable / Enable Card...
... to put all the E&M channels in a line pool, assign it an access code and give that line pool access...
scottb8888 (TechnicalUser)
... target lines for your digits received. Yes you can go in or outbound with the E&M trunks...
... on the T-1 to E&M? (If I do, will outgoing calls still work? & will the carrier have to make the same...
Norstarguy (Vendor)
... on the PRI trunks. I knew you're supposed to do that on E&M trunking on T1's though to get DID's to work...
... this problem before. Got the target lines built, got outbound working fine with the routing, etc- however...
RYLSFAN (Programmer)
...default except changed to E&M. Thats not my fastball, thats my hurry up and get by you pitch...
... could change the disco supo on an E&M line???? thanks for all the help by the way... Thats not my...
Missy8s (Vendor)
...I have a customer with a Norstar MICS with a single T-1 E&M with 9 provisioned channels...
... the cows come home as usual. My T-1 is an E&M Wink with ISD/TT IF Levels so everything with setup...
TGW (TechnicalUser)
...Since this is a T1 check the trunks that are on the T1 either DID trunks or E&M and check the prime...
... if the gen delivery is on but not initialised). Speaking of, how do I make all channels E&M so I can use...
TnPhoneguy (Vendor)
... by dialing 9+ number for the routing codes to take over. All T1s are E & M...
... tables. When a caller tries to use outbound transfer to MB 210 the get a recording. "The routing...

SEARCH AGAIN

Keyword(s):
Subject:
Handle(s):
Scope:

Area:

When:


Sort:

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close