Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by YuanXu

  1. YuanXu

    xp_sendmail

    Hi! When I use xp_sendmail I find problem below: SELECT @sumstr = 'SELECT SUM (fee) FROM FeeTable WHERE...' EXEC (@sumstr) IF @@ROWCOUNT > 0 EXEC master..xp_sendmail @recipients = @recipient, @message = @sumstr, @query = @sumstr, @attachments = 'Result.txt'...
  2. YuanXu

    Hi, all: I have a BayStack 450 swi

    Hi, all: I have a BayStack 450 switch, the system information is : sysDescr: BayStack 450-24T HW:RevB FW:V1.48 SW:v4.1.0.6 ISVN:2 I use a HP SNMP++ Browser (version 2.0) to get some SNMP information from that switch, when I use oid = 1.3.6.1.2.1.17.4.3.1.2.+MacAddress to get switch port...
  3. YuanXu

    How Can I Make My Vlan Up?

    Thanks for your help. I made a stipud mistake. I connected 10M port assigned to that vlan to a 100M port, so they can not connected, and the vlan can not "up". :-(
  4. YuanXu

    some problem with G2948-L3

    hi! I have one data port in the working room, and I have to make three computers to use this data port to connect to Internet. I use a 2948-L3. All the ports were assigned to the same vlan(no ip address), and they can communicate with each other, but the uplink to the data port was fail. How...
  5. YuanXu

    How Can I Make My Vlan Up?

    The vlan configuration is : interface Vlan99 ip address 192.168.99.1 255.255.255.0 ip verify unicast reverse-path no ip redirects mls rp vtp-domain dm mls rp ip the result of "ping 192.168.99.1" is : Success rate is 0 percent (0/5) Can you tell me where the configuration mistake...
  6. YuanXu

    How Can I Make My Vlan Up?

    Thanks, The vlan is "down", but not "administratively down", so I can not up it just by typing "no shut". I think there must be some configuration mistake, but how can I discover it?
  7. YuanXu

    How Can I Make My Vlan Up?

    I added a Vlan to my 5509 Switch, but the vlan status is always as "vlan is down, line protocol is down" ? How can I do to make it up? Thanks!
  8. YuanXu

    Hi, all I get following messages

    hi, thx for your replies. There is only one DDS4 tape driver attached to the system. I tried this morning, find that I can copy files from some DDS3 tapes , but from DDS4 tapes, it still returns "tar: blocksize=0". what is wrong?
  9. YuanXu

    Hi, all I get following messages

    Hi, all I get following messages when I try to backup files from tape: % tar xvf /dev/rmt/0 tar: blocksize = 0 When I try to run mt it appeared: %mt -f /dev/rmt/0 fsf 1 /dev/rmt/0 failed: I/O error. I have no idea with that, so need your help very much!
  10. YuanXu

    How to use two network adapter as one?

    Hi, I have two network adapers in my Ultra60. Both of them are 10/100M. To meet the needs of network traffic, I want to use them two as one network adapter, so that there will be a bandwidth of 200M of my server. Who can tell me how to do this?
  11. YuanXu

    system problem!

    Hi, I find that the problem is that when I neet to "input" something at OpenWindows, the system does not have any response. It is said that is some problem with the display adapter, I asked reseller changed it, now, the problem is resolved. Thanks
  12. YuanXu

    system problem!

    Tuka: Thanks for your reply. How can I get the useful hint from /var/admin/message file? I had checked file system, but that did not work, so I had to reinstall the system from cdrom, but there was no response when the setup process get to the "Hostname Input", that happened whenever...
  13. YuanXu

    system problem!

    Hi, Once my system (solaris 7) was shut down abnormal, there always be no response before the CDE login interface appears. Please give me some advice. Yuan
  14. YuanXu

    Give a common user sys-admin permission

    Hi, that does work. thanks for your kind help! :-)
  15. YuanXu

    Give a common user sys-admin permission

    Hi, Who can tell me how to give a common user the permission to some system administraion tool such as "useradd" ,"fsck". It seems that use chmod only does not work.

Part and Inventory Search

Back
Top