Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by XKent

  1. XKent

    Are optiset E telephones compatible with HiPath 1120 TelCenter?

    System programming can only be executed using the first slot on an analog extension of the interface (default extension 11) equipped with an analogextension (MF) or on a KS-type system telephone or in the first slot of an optiPoint-type system telephone. Is OptiSet E standart KS-type system...
  2. XKent

    Are optiset E telephones compatible with HiPath 1120 TelCenter?

    We are only planning to buy new one HiPath, so i want to know if we must buy some new OptiPoint phones or it is possible to use those OptiSet phones that we already have...
  3. XKent

    Are optiset E telephones compatible with HiPath 1120 TelCenter?

    So i have 2 questions: 1)If Optiset E phones could be used as system phones on Hipath 1120 (in basic config w/o any additional cards installed)? 2)if programming could be performed by using this kind of phone?
  4. XKent

    OfficePoint 150E outgoing traffic problem

    Hi, we have Siemens OfficePoint 150E (with CBPC, STLS4, FMC8, IMOD,V24/2 cards installed). I couldn't figure what happened, but when i trying to make some external call there is the problem: recipient couldn't hear me (but i can hear him). Same problem when i answering on external call... It's...
  5. XKent

    What software i must use for Hicom OfficePoint 150E programming?

    Are you sure that only settings from PBX side is baud rate setting? May be i must configure wich ports on V24 is used for connection/enable this feature/e.t.c.? I had checked pinout of my cable another one time, and it is exactly the same, that described in manual (wich has no difference at all...
  6. XKent

    What software i must use for Hicom OfficePoint 150E programming?

    OK, ofc my nullmodem cable is not original cable by Hicom/Siemens, but it is properly pinned and hooked as you described (V24 interface (DB25) on PBX directly to Com (DB9) interface of PC without any other adapters) ... On PBX side i setted up only 22-13 (baud rate value to 9600) It seems that...
  7. XKent

    What software i must use for Hicom OfficePoint 150E programming?

    Now having problem while trying to connect PBX from Manager software: when i running "Extras>>>Start wizard>>>Hipath 3000>>>V24(Com1)" i always getting error message "Communication system is Offline. Check the cable connection" ... Settings is 9600/8/1/none from both sides; Communication cable...
  8. XKent

    Announcement Before Answering on OfficePoint 150E

    Had ordered Interalia "The Voice" V-22 from ebay. Now waiting delivery... Could somebody answer me about the ports on CBPC card, by wich this announcement device will have connected?
  9. XKent

    Announcement Before Answering on OfficePoint 150E

    As i understood, to use this device, i must have one of the ports (Analog a/b (T/R) subscriber lines) on slot 3 (lower right corner of attached pic) free? In case of using EXM card, in addition i must buy some announcement device? But why i need that EXM card at all? What is the functionality...
  10. XKent

    What software i must use for Hicom OfficePoint 150E programming?

    Thank you, i'll check software version of system soon. My system is DID capable, but i think that managing it remotely by connected PC (TeamView, Remote Desktop e.t.c.) is much easier.
  11. XKent

    Announcement Before Answering on OfficePoint 150E

    Hi, we have Siemens OfficePoint 150E (with CBPC, STLS4, FMC8, IMOD, V24/2 cards installed). The task is to provide the "Announcement Before Answering" service. Which is the best way to perform this? By now i am planning to buy EXM (S30817- Q902 -B401) card, and connect throught it some...
  12. XKent

    What software i must use for Hicom OfficePoint 150E programming?

    Hi, we have Siemens OfficePoint 150E (with CBPC, STLS4, FMC8, IMOD, V24/2 cards installed). As i understood, i could connect it to the PC, using RS232 interface on V24/2 board by NullModem DB25M/DB9F cable. The question is: what software i must use to program/manage this device? In manual...
  13. XKent

    The external lines sporadically became Out of service

    Guys, i really need help! Sometimes trunks working good few days, sometimes they became out of service several times per day... I had tried different ports on BRI card, had changed some line settings with no result.
  14. XKent

    The external lines sporadically became Out of service

    Yes - this is Europe (Greece)... My bad - i didn't mention that, when trunks became out of service, it is not possible to call outside, nor recive incoming calls (( And only thing that helps - it is soft reboot.
  15. XKent

    The external lines sporadically became Out of service

    So we have Avaya IP office 500 with BRI 8U / VRM32 /DS extension cards installed... Connection with outer world powered with two ISDN lines (they connected to the first and third port of BRI card), each line represent two external phone numbers (by MSN). All working good, but sometimes trunk (or...
See more

Part and Inventory Search

Back
Top