Recent content by xevious2k

Hi All, I have a client, (law firm), that just moved to a new location, its a two story house and the workers are downstairs and the lawyers are upstairs. We have a TZ210W, 5.8.x firmware, installed downstairs. The wireless works fine downstairs, but the signal is weak upstairs. We purchased a...

TTTommy, That worked perfectaly, Thanks, A+++ X2K

Hi All, We are using a Partner ACS v5 with Partner Messaging 1.0 voice mail. The system is configured to use the Auto-Attendant to answer the lines after two rings to capture caller id, (which it does), but we are unable to get the system to pass the caller id info to the desktop phones. When...

One other thing... Our t-1 line was only 1.5Mbps and the Cable is about 27Mbps, I know the ports are only 10Mbps, could that have any impact on this?

Thanks Burt, won't "permit ip any any" then allow everything in on all addresses, (basically wide open)? Comcast only gives a mamimum of 13 IP address, so to conserve them, I only want to use 1 IP for NAT The modem is in gateway mode and my linksys home router works great, I just don't want...

Hello, I need some advice. I am attempting to get a Cisco 3620 Router to work behind a Comcast Business Class Modem w/ built-in SMC Router. We are assigned 13 static IP's from Comcast--the Modem/Router uses the .68 address, with the other 12 just below this. According to Comcast, all one must...

BTW, Here is my config... service timestamps debug uptime service timestamps log uptime service password-encryption no service tcp-small-servers no service udp-small-servers ! hostname blahblahblah ! enable password nottelling ! ip source-route no ip name-server ! ip subnet-zero no ip...

Hello, I need some advice. I am attempting to get a Cisco 3620 Router to work behind a Comcast Business Class Modem w/ built-in SMC Router. We are assigned 5 static IP's from Comcast--the Modem/Router uses the .50 address, with the other 4 just below this. According to Comcast, all one must do...

Greetings All, I know a lot of you have been having trouble connecting to your VPN Servers with the later versions of the Linksys WRT54G Routers. After 2 days of working on this, I think I have found a possible solution. At least this worked for us. Here is the equipment we use: Router...

I'm getting the following error message with Outlook 2003 and Exchange Server 2003. Does anyone know how to repair this? This occurs everytime I try to set Delegates for a user, or any user for that matter. I get to the point where I have assigned a user the permissions and when I click OK, I...

Hi All, I am currently running 2 MS Win 2K Name Servers. I am looking to replace these with something newer as the machines they are currently running are at the end of their lives. These servers are outside my firewall and resolve DNS for most of my clients. I am looking for a...

login script is in the sysvol/domain/scripts folder and is called by login script function in AD Users and Computers.

Hi All, I tried searching for an answer to this, but couldn't one that worked. We have 4 servers in our Domain (FPS1 - FPS4). When some users logon the logon script doesn't run. When I check their settings, they are loging onto FPS2, i.e. LOGONSERVER=\\FPS2. If they logon to FPS1, it runs...

Paul, Reverse DNS is fine. xmsre, As soon as I type the letter E I get Connection to host lost. Thanks, X2K

Hi All, I'm haveing a very difficult time resolving this issue and it's beginning to cause problems with our business. Whenever we try to send e-mail to a .ORG domain, we get a delay message and then an NDR. Here is the NDR...(only the names were changed to protect the innocent) Your message...