Recent content by wakeboardTX

OK. I think I've got it. LDID with RLI in NPA programming for local DID trunks and DID for distant DID trunks on-net including route programming at the RDB: LD 16 Type TIE CNVT YES DDMI 5 (references DMI 5)

I have a Meridian 1 Opt 11C ver 2111 rls 25.30+ with 2 TMDI PRI spans. One supports tielines and the other is CO/DID trunks. I would like to reroute DID calls to the PBX at the other end of the tieline over the tielines first, then the CO/DID trunks. I would also like to redirect callers who...

No, Curly. I searched Yahoo for "Flashtalk Programming record" to no avail. I have it now and thanks for the tip!! Dale

Thanks to this forum I have been able to "stumble" my way through setting up CCR on Flashtalk. My setup and operations guide makes reference to a StarTalk Flash Programming Record. I do not have one but thought it may help with future programming. Does anyone know where I can get one? (Flashtalk...

Thanks Don. It does work when I wire up a single line off of the Meridian 1. I suppose I will have to break out the oscilloscope and compare ringing signals between the two.

TYPE RDB CUST 00 DMOD ROUT 2 DES COT TKTP COT PRIV YES SAT NO RCLS EXT DTRK NO ISDN NO PTYP ACO AUTO NO ICOG IAO RANX NO TRMB YES STEP CPP NO TARG CLEN 1 BILN NO OABS TIMR ICF 512 OGF 512 EOD 128 DSI 34944 NRD 10112 DDL 70 ODT 256 RGV 640 FLH 510...

TN 020 0 00 03 TYPE COT CDEN 8D CUST 0 XTRK XUT TIMP 600 BIMP 3COM TRK ANLG NCOS 1 RTMB 2 4 PRDN 5013 CMF NO SIGL LOP SUPN YES STYP BST AST NO IAPG 0 CLS UNR DTN CND WTA LPR APN THFD P10 TRC LOL TKID DATE 8 APR 2009 TN 020 0 00 04 TYPE COT CDEN 8D CUST 0 XTRK XUT TIMP 600 BIMP...

...and I am trying to get it to ring on a multiline set if that makes a difference. (I do have 1FB's working this way on the Universal trunk card in question)

Correction: The Meridian 1 is an option 11C.

I am extending a phone number off of an SL-100 (distinctive ringing off) across an Adit 600 FXO FXS circuit into an NT8D14BB (rls 06) Universal trunk card on a Meridian 1 (Rls 24.24+). I am able to seize the line outgoing from the M1 but cannot get the trunk card to ring through to the line on...

That did it. Thanks NorstarWiz1

Upon further review I have noticed that the inside message was returned due to an extended absence greeting...

I have a user on a StarTalk C2 that has a mailbox that will not accept outside caller's messages. I cannot access the mailbox remotely (using ** login) but can send a message from an onsite mailbox. I do not know how this restriction came into play and therefore do not know how to fix it other...

I have an Octel 350 with Aria 3.00.09-1 software. The system has 4 file cards. If I number them 1 to 4 (left to right) I see that 2 and 4 are the active (ACT) cards and 1 and 3 are standby (SBY). I suspect that the system may have switched CPU's. CPU switchover is set to Normal: N Abnormal: Y...

Thanks for the replies. Pretranslation did it.