Recent content by VIPE

Well, I did it before and nothing. reset system, nada. the only thing left is to delete the mailbox or initialize it maybe this will fix it. I will try that next. Thanks

I have problems with one phone x110 the msg light and feature light are blinking all times, the screen have the VM on but there are no message on the that box, I also check with coosesions if any one have that extension as second message light notification, no luck on that. Some help. Thanks

thanks guy it was the polarity, problems my bad , getting old. I switch it and every thing is back again, thanks

thanks guys, I did an stat on port 18 12 and still showing idle with out phone to it.

Hi to everyone. I have a problem changing a 3905 of TN XXX to 3902 using same TN XXX. I did a in LD20 put OUT TN XXX then NEW with Type 3902. but not working, now 3902 in TN XXX, I'm misssing something? system ver 4.5 I haven't playing with Option 11c for long time, any help Thanks Note: I...

Yes, I only change the type of lines from Analog to digital again pool 899, B channel grp 1, and 898 to B channel 2. ARS , dialing 9 goes first to 899 then 898. and yes if U use 9 from any phone U get the PRI channels. I will check tomorrow the FRL on the VM ports, but I think is the same as the...

Thaks, I did check the ports and all of them have the pool 899 and 898 assigned to them, and still no luck. what I'm confusing is, if with PRI and "NO" CO lines it does work?. Also I put the PC with hyper terminal on the SMDR for output on thous ports, no luck either, nothing prints for VM...

I have a Legend 7 system w/ MM 007 that I installed 2 PRIs, the PRI circuits are fine it just that the customer used to have notification to their cell, after they get messages, but now with this PRI installation some how that stop working, their pools are 899 PRI 1 and 898 PRI 2, the ARS start...

Yes, I do have some PRI problems, first the D CH was down, carrier said that I have the wrong Protcol I was DMS250 now after a day w/o service they told me to change to DMS100 because their swith doesn't supported, dms250, I dont know why now!, anyway after all this, the D ch is back but, the...

I have this problem and it reads 255 times, also I checked the list of events and alarm and is not there, help! MICS 5 /PRI

Hi, every one this is new for me, I got an MICS 5.0 w/ PRI one card and every thing is normal, except for calls are coming at same time on the pri circuit, I mean more that 23 calls at the same time the system goes weird, all phone rings, the display flash, etc and no calls can be answered at...

Well, I trayed to programmed the console for all channels, but it doesn't let me do it, from PRI channels. so I can't use, but I notice that this happen channel 5 going down from one,I mean the 5 th call, when the 6 th channel is being use for out going call, it shows "no free line&quot...

Ok, I will program the channels to be on a DSS console, that way one by one will be tested. all 23 channels are provisioned. some one knows where I can get an update list of alarm and events for nortar 5 or 6.? Thanks

Hi, I got a MICS 5.0 w/ PRI, so far every thing looks fine, my routes are fine, destinatin code also fine, and calls are going out, but some time I notice that only one chanel will be in use and maybe two chanel and when another call is place on the pri it shows "no free lines", or...

Yes, I got the same problem, error 501, I don't know. but I guess it have to be with the old version is not completly remove or XP admin rights,because before I was using ver 9.0 and I didn't have the error at all, then I up grade to 9.1. mabye it's some thing with the XP admin. If some one...