Recent content by vbportal

OK, thanks ! - now to try to find them and see if it works

BadBigBen - that sounds logical but did you conclude that somehow from the tables ?- I can't figure out the tables. If I look at the first table : column 1 - device column 2 - 1 DIMM - I presume it means 1st slot column 3 - 2 DIMMS - I presume it means slot 1 & 2 column 4 - 3 DIMMS - all 3...

were you actually able to read the scanned image ?- I tried saving the file from the link and magnified it but can't read it (directly from the link it's too small) It is the Gigabyte P4 Titan 533 GA-8IEXP motherboard (845E chipset) The manual indicates the following regarding memory on page...

I'm having problems with the scanned image - how should I make the scan so that the image is visible in enough detail (photobucket reduces it and you can't read it)?

I want to add memory to my pc. The instruction manual (scanned image below) describes the DIMMS to be used but I don't get it - I just don't understand how they get the MB figures for the 1,2 and 3 DIMMS in the table and how the "banks" are figured into it - did read a bit on the web about...

OK thanks ! Just curious - you mentioned "free programs" - are there better tools which need to be purchased ? (just so that I know which tools are being used - will try to learn as much and get the most out of SysInternals before purchasing anything)

At the moment I'm just a user with basic knowledge of XP. Could someone indicate whether there are tools or specific knowledge one can master to be able to in-depth diagnose problems/faults etc. ? (at the moment I know of the event logs but can't get very far with them either ;) ) Some...

I've gone through some self teaching on networking and have a basic grasp of addressing, ports and basic firewall rule setting but frequently when I allow the firewall to query whether certain communication should be allowed, I come across communication which I am not sure where it originates...

I looked at the instructions again - as you indicate auto should recognise router/AP functionality but OFF=AP and that is what I had uptil now. Not sure why you mention to use no cable in the WAN port ? Yesterday I connected the AP (set to OFF=AP) via blue port (WAN port) to the switch to which...

Well I spent a lot of time getting nowhere to confirm what I already knew - I have a lot to learn about networking/protocols and windows. I worked on PC1 which has the internal NIC and software for usb wireless adapter, with following connection: router - AP -PC1 The AP (router turned off) is...

I used the PC1 which had the NIC connected to the AP switch for the test. With wireless USB disabled and NIC enabled, I can ping the AP and the router and go on internet. With wireless USB enabled and connected and NIC disabled, I can ping the AP but not the router. I have windows firewall and...

I have the following scenario D-LINK router - D-link switch - Buffalo AP - PC1 !-- PC2 Not sure if the "ascii" will come out right, so it's the D-link router connected to D-link switch, which is then connected to a Buffalo Access point + PC1 and PC2...

Hi, I have a logitech quickcam installed. Upon startup in a normal user environment I get a small window with "Error, Access is denied" (which I can repeatedly click on and it disappears) + error reports: LogitechQuickCamStartupApplication QuickCamAlbumDatabase This does not happen when logged...

Hi, I started recently at this company and inherited the following: ProLiant ML150 server with one 36GB SCSI hard disk. Hard disk partitioned C:Windows, D:accounting package + data There is no backup yet. There are some 40 PCs. Accounting and sales people use the accounting package...

Hi, Newbie question: I wrote this short test code to try to remove duplicate bitarrays from an arraylist - could someone please give me a hand (thought bitarrays is "built in" so it should work or is "Equals" not working with IndexOf because BitArrays are in the ArrayList? or ?)...