Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by UTTech

  1. UTTech

    Offline file and Read-Only

    I have Offline Files enabled on a folder on the network. While still connected to the network, when I try to access a file, sometimes it opens with "Read-Only". The file is NOT a read only file and this only happens occasionally. If I disable the Offline files, this does not happen anymore. Any...
  2. UTTech

    can't change inside ip range

    I tried adding the Static Route to the new IP and then when I tried to change the internal ip, I get the following message: Cannot remove route entry because it does not exist.
  3. UTTech

    can't change inside ip range

    I am also new at this so bear with me!! I want to change the inside IP address also. It says above that I also need to change the nat statments and access-lists. Can I do this on the PDM? If so, do I change the NAT under Configuration-Routing-Static Route? What about access lists? Where do I...
  4. UTTech

    Disable NAT

    That didn't work. Basically, we created a VPN from out site to another site using Cisco PIX Firewall. When we ping the remote site with a workstation here, the IP address is translated to the server IP address. NAT is enabled on the PIX so I want to disable NAT on the server. Is this possible?
  5. UTTech

    Disable NAT

    I will try it. Thanks!!
  6. UTTech

    Disable NAT

    Yes, I would like to disable translation for specific sites.
  7. UTTech

    Disable NAT

    Well is there a way I can disable NAT to certain addresses?
  8. UTTech

    Disable NAT

    2000 Small Business Server Is there a way to disable Network Address Translation?
  9. UTTech

    Disable NAT

    2000 Small Business Server Is there a way to disable Network Address Translation on ISA?
  10. UTTech

    Cannot access Cisco VPN through ISA

    Update: Small Business Server 2000 ISA 2000 with Proxy enabled Cisco PIX Firewall 501e We are trying to setup VPN with another site with Cisco PIX but running into problems with ISA. I can ping to the other VPN site from the server and the workstation. The problem is that when I ping from the...
  11. UTTech

    Cannot access Cisco VPN through ISA

    Small Business Server 2000 ISA 2000 with Proxy enabled Cisco PIX Firewall 501e We are trying to setup VPN with another site with Cisco PIX but running into problems with ISA. From the server, I am able to ping the other VPN site. I cannot ping the VPN from a workstation. Workstation IP is...
  12. UTTech

    Need to open ports on ISA 2000 Server

    I am trying to connect to a Citrix Server but ISA is blocking it. I opened ICA port (1494) but still cannot connect. What other ports do I need to open? Thank you!
  13. UTTech

    PcAnywhere Ports open but still cannot use

    If I do disable "deny any ICMP", what will that do? How do I check to see what ports are open and closed?
  14. UTTech

    PcAnywhere Ports open but still cannot use

    Yes I am trying to connect to a PCAnywhere host outside from inside. I noticed that if I delete the "deny ICMP", it works. However I do not want to disable that.
  15. UTTech

    PcAnywhere Ports open but still cannot use

    PIX Version 6.3(1) interface ethernet0 auto interface ethernet1 100full nameif ethernet0 outside security0 nameif ethernet1 inside security100 hostname hostname domain-name domainname.com fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http...

Part and Inventory Search

Back
Top