Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by undertaker48

  1. undertaker48

    Setup VOIP Phone

    Jim9776, our Cisco Call Manager is version 4.3 and the phone is a Cisco IP Phone 7911, Please point me in the right direction, Thanks Your Help Is Greatly Appreciated. Thank You Undertaker48
  2. undertaker48

    Setup VOIP Phone

    Thanks Jim9776 you have been very helpful, I'll check for the verison of the Cisco Call Manager and what model Cisco IP Phones we are using and get back with you. Thanks Again. Your Help Is Greatly Appreciated. Thank You Undertaker48
  3. undertaker48

    Setup VOIP Phone

    We are going to VOIP Telephones, and I'm taking a VOIP course to understand the technology, but it hasn't walked me through, on how to set up a VOIP Phone, I found a web site that showed how to set up a VIOP phone step by step, but I can not locate it anymore, hopefully one of you can help me...
  4. undertaker48

    Four and Five Extensions

    We are slowly changing to VOIP telephones, but at the present we have two types of telephones, VOIP and Nortel phones, the Nortel telephones have 4 digit extension numbers and IP phones have a 5 digit extension numbers, we have a TIE(PRI)between the two PBX's and I have DID's here for local...
  5. undertaker48

    Four and Five Extensions

    Where in the Nortel Meridian 61C can I program the pbx to accept 4 and 5 extension numbers to ring nortel telephones and IP telephones, the nortel phones have 4 number extension and IP phones have 5 number extension numbers, which ld to make changes and what I should be changing to make this...
  6. undertaker48

    [b]Changing Octel 250[/b]

    Hi All, Logged into Octel 250, at main menu, went to # 1 System Parameters, then went to # 1 Change Installion Information, and Changed Number of Digits in Extension, Changed Used for Outcalling and ECP from 4 to 5, also changed Used for Message Waiting, also changed the Sucscribers Extension to...
  7. undertaker48

    [b]Changing Octel 250[/b]

    Hi all, I don't know if this possible, but here goes, Is it possible for the Octel to be programmed so it will transfer 4 and 5 digit extenisons, I went in and changed it to 5 digit, but it would not except a 4 digit exrenison number, so I had to change it back to 4 digit, the reason for this...
  8. undertaker48

    PRI TIE NI2

    John, They set up the dch for loop 18 as dch 18 not dch 2, so when I found that out, I got everything back up running, Thank you for your help, it is greatly appreciated. Your Help Is Greatly Appreciated. Thank You Undertaker48
  9. undertaker48

    PRI TIE NI2

    Hi all, John, I disabled dch 1 and can't disable TIE loop 18, I took the the steps you sent me, Thanks, but now my loops are down, making no calls, so do I need to take out the DCH, to get my system back, let me know what I should do. Thanks Your Help Is Greatly Appreciated. Thank You Undertaker48
  10. undertaker48

    PRI TIE NI2

    John, I'm trying to disable loop 18, I disabled dch 1, but it will not let me disable loop18, I get Err PRI010 Disabling of this loop not allowed, associated dchI must be disabled frist, can you help Your Help Is Greatly Appreciated. Thank You Undertaker48
  11. undertaker48

    PRI TIE NI2

    John, where do I check the qsig, this my first pri tie change, thanks Your Help Is Greatly Appreciated. Thank You Undertaker48
  12. undertaker48

    PRI TIE NI2

    John where do I print all these loads, so I make sure I put everything back like it was except, for IFC. Thanks Your Help Is Greatly Appreciated. Thank You Undertaker48
  13. undertaker48

    PRI TIE NI2

    I have a Nortel Meridian 1 61C, need to change the IFC from SL100 to NI2, Software version Seccions 4.5, can you give me the procedure on how to change this, What loads and what order to complete this procedure, I have 1 DCH with daughter board, the daughter board is my DID, any help would...
  14. undertaker48

    Octel 250

    Ken Means, I went to 12 then 2 and I got this response: Integration Error Investigate System Environment 00000 82C00202 F9000000 28000B7E Eac10100 00010 51030000 21000001 51030000 00000004 00020 00E00300 990FFFFF CoD40100 00000000 00030 02212001 022504FF FFFF0000 00000000 00040 02216001 00414141...
  15. undertaker48

    T1, Tie Trunks/Channels

    John the Phone guy, Thank You for responding so quick, I have to take the TIE out and build the PRI the way I want it set up, where can I find the instructions to do this procedure. I've searched the FAQ and I've searched the Posts by Keywords, but with no luck, I'm suppose to go to Texas for...
See more

Part and Inventory Search

Back
Top