Recent content by ttcsbarry

I'm trying to build an ACL that permits traffic from a specific network egressing on a specific port, but also logging the event. any suggestions?

Here's what I did to fix this: Menu 5-1 Use Area Code Restriction Table Lookup for ECP Transfers (Y/N): [highlight #FCE94F]Y[/highlight] Menu 5-2 Menu 5 - Outcalling Parameters BEETHOVEN - Area Code Restriction Table - Area Code: [highlight...

I am having an issue with the Reply by Calling feature (Pressing 88 after listening to a message). No matter what subscriber sends the message to whatever mailbox, reviewing the message and pressing 88 always returns the caller to the same digit combination, even though Octel says " Transferring...

thread923-1292539 Was anyone able to figure out what fixed the issue in the above referenced thread? I have an Octel 350 and an Avaya PBX. We recently change our dial plan on the pBX for 10 digit extensions (with 4 digit short code dialing). At the same time, the Octel was changed to 10 digit...

Does anyone have the Extremeware 7.3eb43 files for Summit 200-24 and Summit 400-48. Specifically image file v73e0b43.Wxtr and image file v73e0b43.Cxtr I need them to upgrade 2 different summit switches from versions prior to 7.3. I have the 5.1 BootRom for both model switches. Extreme's eSupport...

Can you remotely start up an S8710 after a planned shutdown? In other words if you remotely shutdown a server and uncheck "Restart after shutdown", can you remotely restart the Server once commercial power is restored? They are doing a planned power shutdown because of the Power Utility company...

See Bullet point under Call Vectoring Interactions for Attendant Conference This section provides information about how the Attendant Conference feature interacts with other features on the system. Use this information to ensure that you receive the maximum benefits of Attendant Conference in...

How can I contact you?

I have a remote S8800 Server in another city running CM 5.2. I was following an Avaya document to add a new login to have the same permissions as dadmin. But, I believe that I made a mistake by selecting Web Access Mask and choosing “Change Access Base Mask” and changed it from 10000 to 10020. I...

I have added a port, port 20 as a trunk port with the Default vlan untagged and vlan ManageVLAN tagged. I am trying to add this port to STP s0. I am getting this error: Error: Cannot add VLAN ManageVLAN port 20 to STP domain s0 The command I am entering is: configure stpd s0 add vlan...

I need help with NAT. I have an Extreme Summit 300-24 with Extremeware Version 7.4e.2.6. I have 2 VLANS 192.168.255.0 /24 and 12.151.200.240 /29. I have a device on the 12.151.200.240 /29 network that connects to the internet. I want to NAT all of my 192.168.255.0 /24 devices to the...

I need help with NAT. I have an Extreme Summit 300-24 with Extremeware Version 7.4e.2.6. I have 2 VLANS 192.168.255.0 /24 and 12.151.200.240 /29. I have a device on the 12.151.200.240 /29 network that connects to the internet. I want to NAT all of my 192.168.255.0 /24 devices to the...

AvayaTier3, That makes some sense. The S8500A where it won't work is CM 2.2.2 and the units I tried it on are at 3.1.5. An older Addonics Model AESDMD4U2 seems to work, but I can't leave it there. Where do I find the patches for adding the drivers for CM2.2.2? Is there a special procedure for...

I had to replace the Flash Drive on an S8500A because the backups would fail intermittently and would require a reset to the flash drive to get it to work again. I got the new flash Drive (Addonics AESDD12U2) but I cannot get it to work on this server. I have tried it on S8710, S8500C and...

Hardware platform is S8500B's and S8500C's. Software is 3.1.4, 3.0.0 and 4.0.1. There are several sites. They have Tenant Partitioning. It all started with one site (S8500B with CM 3.1.4). Because of the time zones and the reluctance of the staff to take time to test with me, I then started...