Recent content by torner

Is ANYONE using OS X with the latest iteration of IE 5 for OS X and Novell BorderManager? I can't get it to work through the proxy at all. Any help (besides the obvious 'ditch the Macs' option) is appreciated.

I have an ASN with multiple 34000 10BT ENet interfaces. I am removing an old 'ADV' copper switch and an old 'ADV' fiber switch and replacing them with BS350 24T's with fiber cards. I need to know how to set-up the cross connect back to the ASN's 34000 card. Will the ASN's 34000 card accept...

I have an extra PowerR iMac video out interface which was purchased at least two years ago. It was pulled from a 'deceased' iMac. Now, I need to install it in another iMac. Unfortunately, I don't have an archive copy of the installation guide AND the tech didn't note how it was installed...

Snootalope...thank you for your input. Were you able to slay the beast? Speaking of input, here's more from me: * The client is set to use IPX as the primary protocol... * The IP addys and all associated settings are static (private net numbers: 10.93.xx.xx) Keep those cards and letters...

Dell Latitude C640, port replicator dock, NWare client 4.83 SP1. Unit is plugged into a Nortel 350-24T switch. More times than not, the user is getting a "can't see tree" error when booting. User has to login 'workstation only' then launch the NWare login in order to attach to the...

I am semi-successfully using Macintosh OS 9.0.4 through 9.2.2 computers with Internet Explorer 5.0 through BManager 3.7/Cyber Patrol. I was fortunate enough to have a user from Italy send me a 'contact Microsoft for this file' file. On my own I found that I must turn off Virtual Memory and...

To everyone who replied...THANK YOU! I have given up on the drive. Using ALL of the tools suggested here, and a few more, the drive just would not mount. It was recognized by many of the applications...just wouldn't mount to get the info. The data was not important enough to warrant paying...

If you bought the RAM upgrade from a 'real' vendor (versus eBay or a friend), I suggest that you contact the vendor to request a new module. Also, make sure the chip is indeed compatible with your system. According to my source, it should be: SDRAM, PC100 • CL=2 • Non-parity • 8ns • 3.3V •...

II have stopped purchasing UMAX scanners because of their plans to CHARGE for all driver/software updates (versus free download). I have switched to Epson. As for your specific issue, I believe that the UMAX suggestion is a good one so long as you haven't modified the factory OS load. Both OS...

Thanks for the tip! I completely forgot about SCSI Probe (v5.2). While SCSI Probe DID see the drive, it would not mount it. The error is: "SCSI error: -7932 (2) Sense 4 (1) Failed: logical units not supported" I'm ready to chalk this drive up as a lost cause. The end user has...

You should purchase a device called a scan converter. There are several available in a wide range of prices and features. These devices take the output from your computer and convert it to composite video. You should be able to go to your favorite onlone 'warehouse' and search for 'scan...

I have a similar set-up w/ Adelphia: CABLE MODEM // ROUTER: Linksys 4 port 10/100 // AIRPORT (1 ENet) and AIRPORT (2 ENet) I also have an 8 port dumb hub and Compaq PC attached to the Linksys and a Farallon ATalk to ENet adapter for my HP LJ5MPattached to the dumb hub. The Linksys does the...

I have a Seagate ST39140N 9GB SCSI HD in an external case. Unit will not mount. Silverlining SEES the drive and will mount it. SLining will not, however, actually place the drive on the Desktop. SLining says the driver is damaged and that I should run 'setup' to place a new driver on the...

Does either the NW Client for Windows 95/98 OR the NW 5 NOS offer the ability to define a length of idle time which, once met, will lockdown the desktop/network access until the user's network password is entered? I must give a group of teachers full access to administrative network folders...

Will ackka's batch file solution work to restore other IE settings? Most specifically, I'm interested in the proxy settings.