Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by togtek

  1. togtek

    Upgrade Firmware for OpenStage 60 HFA

    Hi Ya, The latest current version is V3 R0.33!! Released just last week. Is available from the UNIFY partner portal download center is you have log in credentials you can easily obtain this. Not currently on the OSBiz image as yet, but V2 R1 being released very shortly will rectify that. Its...
  2. togtek

    Realitis DX - hunt group question

    Hi there, I,m afraid that there is no such function on a Realitis DX. The "Hunt Groups" will only do Cyclic (Distribution Group) or Linear (Hunt Group) searching on incoming calls. The only way to get a Realitis DX to call a group of phones simultaneously is probably with the introduction of...
  3. togtek

    DPNSS Message block trace Supplimentary Service Message code unknown definition. (BTNR 188 or 189)

    Thanks SBCSU, I had been through that document, but was searching for *248!!. Its is exactly correct as the extension we used to test this call has an "Immediate Forward" active on it. Thanks for helping with the clarification of the message anyway. Kind regards Simon
  4. togtek

    DPNSS Message block trace Supplimentary Service Message code unknown definition. (BTNR 188 or 189)

    Hi there, I have been trying for a few weeks now to discover the definition of a DPNSS "Set-UP" message I believe is causing an issue with routing calls over a private network. The initial service request message (ISRM) is as follows:- "> R01909 SSRM(I)...
  5. togtek

    Xpressions Version 5 EXCH Email interface not funtioning correctly.

    Thanks for the info, I will be talkwing to the customer IT department about the password as it does look as though that's the issue to me also.
  6. togtek

    Xpressions Version 5 EXCH Email interface not funtioning correctly.

    Can anyone shed any light on this subject for me. We have a customr with a unified Xpressions Version 5. On the Voice side of things, everything appears to function as expected. However, most of their user have the voicemails transmitted to their emails as an attachment file. The Xpressions...
  7. togtek

    IP Trunking HiPath 3000 and HiPath 4000

    Hi Denis, Well done for translating the documantaion in the document I attached into the later AMO's I did give a quick glance yesterday when I was actually on a V5 switch during the day, but I hadn't had teh chance to log in and add this to the thread. Glad to have been of some help at...
  8. togtek

    IP Trunking HiPath 3000 and HiPath 4000

    Hi If you are referring to GKREG:99 above it is the IP address of the HG1500 card. As for the SIP tab on V8, I am assuing youmean the SIO settings on the HG1500 card. These should be ignored as you are using CORNET-IP (H323) and the TRUNKS should be configured as such in the IP Trunk Section of...
  9. togtek

    Hiparg 3500 Version 7 Speed Dial List Update via Manager E

    Hi guys, Apparently, if there is a customer password set and they have accessed the System Spped Dials in the menu, then it is taken away from the Engineers level users. The solution is to log in as the customer and it re-appears!!! Job Done!! Thanks for the suggestion though!. Cheers Simon
  10. togtek

    IP Trunking HiPath 3000 and HiPath 4000

    Hi Denis, How have you got your GWDIRNO configured in WABE? There are two methods available, i.e. Closed numbering or Open Numbering. Closed numbering would require you to set the number up as a STN with an NWLCR configured to access the Gateway card trunk group with a specific "DestNo". Or...
  11. togtek

    IP Trunking HiPath 3000 and HiPath 4000

    Thanks for the reminder Iamnothere, Wasn't thinking about the version when I replied. I'd forgotten that there are some new AMO's to consider. BFDAT for IP Gateway Board configuration. for one. Am looking for a more up to date document now. Stand by!
  12. togtek

    shutdown of hipath 4000

    Hi, The previous answer is sound up until the point of switching the system off! It would be far nore advisable to use the folowing AMO. EXEC-REST:SYSTEM,RELOAD,STD; This will restart the RMX and the UNIX. Be patient, these babies take time to load. Even the new ones!! Good luck Togtek
  13. togtek

    IP Trunking HiPath 3000 and HiPath 4000

    Hi Denis, H4K documant attached to this answer. Regards Simonhttp://www.mediafire.com/?3clp1jc6831lbhv
  14. togtek

    IP Trunking HiPath 3000 and HiPath 4000

    Hi Denis I have some documentation that could be helpful for you for both the 4K and the 3K. However I do not seem to be able to attach them both easily. Si I have had to set two answers with different attachements. Kind regards Simonhttp://www.mediafire.com/?o6uffs5x7u8lw69
  15. togtek

    Hiparg 3500 Version 7 Speed Dial List Update via Manager E

    Hi I have recently become more involved with Hipath 3000 and have noticed that we hae a number of Version 7 systems that do not show the System Speed Dialling 'tab' is not shown under System Parameters sub menu. Is this function not available at Version 7? Many thanks in advance.
See more

Part and Inventory Search

Back
Top