Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by telnettech

  1. telnettech

    Configuring AudioCode E-SBC for Remote Users

    Anyone with an idea about this? Anyone? Brian To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!
  2. telnettech

    Configuring AudioCode E-SBC for Remote Users

    Looked on the AudioCode website and i do not find anything that would suggest that this is possible. does anyone know or have a working config for a remote office to use the SBC to make connection and register with the PBX that is behind the SBC. So in other words i have a PBX connected to an...
  3. telnettech

    Cisco 5330

    Ok next question. We are not using CUBE. So is the configuration the same???? Even though we are not using SCCP, do I associate the SSCP application to the profile????? Still not fully clear on that part To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!
  4. telnettech

    Cisco 5330

    Right....But as you can see, I dont see the hardware at all. I cant create a DSP farm unless the device sees the hardware. I have shutdown the router and reseated the DSP and the module to no avail. I do see this in the Show Run command that has nothing with it and have placed them into a dsp...
  5. telnettech

    Cisco 5330

    whykap, Yes I see them when i run the show diag command. PVDM Slot 0: 64-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card Hardware Revision : 4.0 Part Number : 73-8541-05 Board Revision : A0 Deviation...
  6. telnettech

    Cisco 5330

    I dont see anything that stands out. If I recall, there is normally a module name in the show hardware command. See below the output. Sprint5350# sho hardware Cisco IOS Software, 5350 Software (C5350-JK9SU2_IVS-M), Version 12.4(15)T3, RELEASE SOFTWARE (fc1) Technical Support...
  7. telnettech

    Cisco 5330

    I have a Cisco AS5350XM Router running IOS 12.4.15T3 and added 6 PVDM-264 in a module. When i look at the show voice dsp active, i only see 48 DSP. I think there is something i am missing like some configuration. I have looked around google and dont seem to find anything that can help point me...
  8. telnettech

    Avaya IP 500 SIP Trunk Setup

    thread940-1375906 ITSP says that they dont need a FQDN (Full qualified domain name) can you put the IP address in this field or do you leave it blanK??? Can you set this up without a FQDN??????? To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!
  9. telnettech

    Cisco Interface with Vodavi XTS----PRI Handoff issues

    All, Have a customer that from time to time has to restart their phone system or the cisco router that we have on site doing a SIP to TDM ISDN-PRI handoff to them. it appears that the messaging between the 2 pieces of equipment seems to get messed up during an overnight time period and customer...
  10. telnettech

    PRI handoff from a Cisco 2431IAD to a VoDavi XTS

    Jim, thanks for the reply. To answer your questions yes I work for the provider and am responsible for the Cisco router. What is being reported is that no inbound or outbound calls can be made or recieved. The settings on both seem to be fine. There are calls being passed between the router and...
  11. telnettech

    PRI handoff from a Cisco 2431IAD to a VoDavi XTS

    All, Have a customer that from time to time has to restart their phone system or the cisco router that we have on site doing a SIP to TDM ISDN-PRI handoff to them. it appears that the messaging between the 2 pieces of equipment seems to get messed up during an overnight time period and customer...
  12. telnettech

    Sylantro Failover

    Does anyone here know anything about Broadsoft Sylantro softswitch???? We are on an older version and have trouble with failing over from a nonresponsive gateway to a working gateway on the same call. Willing to pay someone a contractor fee to assist in resolving issue. Send me a PM Brian S...
  13. telnettech

    Making test call thru Voip dial peer

    All, I am using a Cisco IAD2431-8FXS with IOS software version 12.4.12. Is there a command that will allow me to test an outbound call thru a VoIP dial peer. I know about csim start <phone number> but that does TDM only not Voip. thanks for the help To error is human.....if the machine doesnt...
  14. telnettech

    Need a dependable VoIP carrier

    I would recommend Lightyear. they have good rates and good service. www.lightyear.net To error is human.....if the machine doesnt work, then KICK IT !!!!!!!!!!!!!
  15. telnettech

    T38 using Analog Voice port on IAD 2431-8FXS

    Does anyone have a working configuration for getting T38 to work when faxing outbound/inbound using an analog voice port on a Cisco IAD2431-8FXS. We are using 12.4.12 IOS software. I have included my current configuration for this device below. I am able to fax fine except when it is longer than...
See more

Part and Inventory Search

Back
Top