dlesap,
Thanks for the reply, I will be on-site tomorrow, and will check the chassis. The MIRAN card is in slot 8 already, so I guess that won't matter. I did set the IP type to static as well.
Hello,
I am currently working on trying to ethernet-enable a MIRAN III card on an Option 61C. I have set the IP Parameters using the Management Console, and rebooted the card. I have connected a working patch cord from the Audio Adapter to the C-LAN switch. One thing I did notice is that...
Hello,
Figured I would post back, since I finally solved this issue last week.
The fix was an outbound CLID table issue.
Phone A had:
key 00 scr xxx 4
Phone B had:
key 00 scr xxx 0 (default)
After looking into the CLID tables, the default, which most phones were set to use, was...
This is for Site A
OK, Here are the SPN's
SPN 1800
FLEN 0
INPL NO
RLI 3
SDRR NONE
ITEI NONE
SPN 1866
FLEN 11
ITOH NO
RLI 3
SDRR NONE
ITEI NONE
SPN 1877
FLEN 11
ITOH NO
RLI 3
SDRR NONE
ITEI NONE
SPN 1888
FLEN 11
ITOH NO
RLI 3
SDRR NONE
ITEI NONE
The Route List Index
RLI 3
ENTR 0...
janchundia,
Yes, I just called site B, and the numbers go through fine. They claimed this started happening after they moved locations. Now the only thing that would have changed would be the circuit. Could this be a carrier issue?
Here's what the DCH msg shows for the failed call.
Note: Numbers have been changed to protect the innocent.
DCH 3 OMSG SETUP REF 0000000F CH 1 15 TOD 15:23:18
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:303xxxxxxx NUM PLAN: E164
CALLED #:10491866xxxxxxxNUM PLAN: E164
DCH 3 OMSG DISC...
Hello again,
Getting back to this situation again....it's still not resolved. I now have one person in particular, whom I volunteered to be a Guinea Pig. He can dial some toll free numbers, but not others. For example, he can dial 1-800-xxx-xxxx, but not 1-800-yyy-yyyy. The call returns a...
johnpoole & PERRYPJ,
Thanks for the info from both of you. I am just going to change the CLS on their sets and be done with it. Once again, I appreciate the help!!
Thanks for the reply,
On the PBX phone, CLS is UNR
Other phone, CLS is CTD
Here's the kicker, and I quote, "This was working a week ago."
I can easily change all phones with CTD in CLS to UNR, but I guess I don't really understand why. Doesn't a phone with CTD use the NCOS to determine...
Hello all,
This doesn't make sense to me, and I was hoping someone could shed some light on this, tell me where to start looking.
A----PRI----B----PRI-----C
|
|(T-1)
|
Central Office
Customer site A has an Option 11...
Hello,
Definitely an end user issue, they weren't reading the dislay back to me properly. They freaked after seeing 'not init'. Thanks for the help everyone, now I have to sell them on a FastRAD.
I'm gonna give the customer a call, tell them to slow down, and give me exact information. Sorry to involve all of you in this issue, it's probably an O E problem. I will post back with results, thanks again to all!!
Class of Service on the mailboxes are set to 1.
The number of Outdial Channels are set to 1. I know this was set higher last time, but shouldn't it still take with 1 channel??
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.