Recent content by tekguy88

Burtsbees, I didn't know one was able to transfer the IOS between routers. I would assume you need to use a crossover cable for the 2 routers. Do you know the Command to transfer the 12.0 IOS on my 2520 to my 2511? Tekguy88

My RAM & Flash are both 8mb in size and I have another 2520 router that has the same with 12.0 enterprise to be able to handle this version of the IOS.

Yes, Smartnet now I recall. The little hamster in the wheel is starting to fall asleep as I'm trying to get back in the game. :-) thanks for the reminder.

I've got a Cisco 2520 router with IOS version 11.2 and would like to upgrade it to 12.0 or higher enterprise edition. I understand you need to be a vender, CCNP, CCIE and other requirements that I do not fit into this criteria. I heard there is a site that you pay a small fee to be able to...

Hello Baye, Your advice cured that annoying problem. It's been quite awhile as I did not get around this problem till recently. thanks again. Tekguy88

I'm getting this error message of: loading routera.cfg loading cisconet.cfg Cisco 2520 router when idle. Router works fine otherwise, but gets annoying time after time. I'm very new to the cisco world and think that this error message comes on after I tried to erase the...

Funning thing happened upon a purchase of my Gateway E-macine T2742 tower. Upon reformatting it with W2KP SP4 I am unable to start up or power up the computer without removing both the CMOS and power cord. I've tried putting it in standby or hibernate to no avail. Although it comes preloaded...

Andy, Thanks once again for your helpful insight. I am waiting for this person to give me that info. you are asking for, but am anticipating he is not as knowledgeable as you and may not be able to comply with that info. The 8510 switch you sold on ebay, is this a blade or an entire stand...

Andy, Thanks for your reply! That cleared up most of my questions, but had one more I'm hoping you can clarify as well. I'm genuinely new to this so I hope you can be patient. I am in the midst of considering a 5505 catalyst and although it's bulky and heavy I really don't mind this as if...

I really aprreciate the reply and infomation to my question. The 3550 is very pricey for my budget and was wondering if I were to get either the 3512 3524 or 3548 that I may be able to do some, but not all of the layer 3 applications? I was also under the assumption that VLAN trunking is a...

Can anyone recommend the best layer 3 switch on the used market for it's cheap price? I've checked prices for the 5505 & 3550 but these are out of my league in price. If anyone has experience configuring a layer 3 switch that knows for certain if let's say a 3512, 3524 or 3548 can do layer 3...

No matter what I do I keep getting this error message provided below. Can anyone help or seen this error message before? It is for a CISCO 1924 Switch. Diagnostic Console - Systems Engineering Operation firmware version: 0.00.00 Status: invalid Boot firmware version...

No matter what I do I keep getting this error message provided below. Can anyone help or seen this error message before? Diagnostic Console - Systems Engineering Operation firmware version: 0.00.00 Status: invalid Boot firmware version: 3.02 WARNING...

Vipergg, God damn I'm a dummy. I did use the site you sent me and when I saw a certain command............can't recall right now, but I thought to myself this can't be it. But, upon confirming to really complete the password recovery process............IT WORKED!!!! I appreciate your time in...

Hello ALL, I have 3 Cisco routers and 2 switches currently and have gotten a grasp of networking some labs with these hardwares thus far. I would love it if someone can direct me to one simple network connecting 1 router, 1 switch and a pc workstation so that I can do more labs. I've tried to...