Recent content by SuperJan

Hi We eventually passed this to Sun and at first they said they would change the system board with the latest OBP. Then we got an email from another Sun engineer, see below: Checking the explorer i notice the following in the etc/system: "set rlim_fd_cur = 128" Why the errors: It means the...

Hi Thanks for the advice. The problem was due to a network error, nothing to do with the server. Someone messed up with cabling switches, trunking etc. I should have known it wouldn't be the server. Thanks again for the posts. Regards Janis

Hi Morefeo There are no NFS mounts on this server. We have one ethernet card and bge0 is configured. From reboot messages: bge0 registered bge0: link down (initialized) bge0: link up 100Mbps Full-Duplex (initialized) I was speaking to our Network guy and he thinks there may be a problem with...

Hi We have a Sun V210 showing errors in the messages file. Can anyone shed some light on what it is telling us? We applied the cummulative patches on Feb 13, but no other changes were made to the server. SunOS sunlegato 5.10 Generic_127111-06 The message file shows these errors: May 8...

Hi We are having problems booting to single user on a V240 server running Solaris 10. The messages which appear on the console are: init: Could not duplicate legacy template - bad file number init: Could not duplicate startd template - bad file number init: Could not duplicate process bundle -...

We are testing sftp but when we tried to send a file to our remote site this error appeared: unable to initialize mechanism library [/usr/lib/gss/gl/mech_krb5.so] xmalloc: zero size lost connection We checked for similar errors and a suggestion was to add the following lines to...

Hi daFranze I have just installed another FC tape library, a Scalar i500. The two FC tape drives are zoned in the fabric and I created a zone for the server so it could see the drives. This has worked perfectly and Solaris has assigned the device paths /dev/rmt/2cbn and 3cbn to the drives...

Hi bombcan I have just installed another FC tape library, a Scalar i500. The two FC tape drives are zoned in the fabric and I created a zone for the server so it could see the drives. This has worked perfectly and Solaris has assigned the device paths /dev/rmt/2cbn and 3cbn to the drives. This...

Thank-you Franz, We are having ongoing discussions with EMC about this problem, I have tried your suggestion. One thing I've noticed is that the Physical path of the devices in luxadm is as follows # luxadm inq /dev/rmt/2cbn INQUIRY: Physical Path: /devices/pci@9,700000/lpfc@2/st@2,0:cbn...

Thanks 605. Have posted a query on the Solaris forum to see if anyone can assist. Bye SuperJan

Hi We are having a wee problem configuring the FC tape drives for Legato Networker on our Sun servers. I have already posted my query on the Networker forum and have been told it may be a Solaris OS or driver problem. When I run "inquire" on one of our servers I can see the 4 LTO3 drives...

Can anyone help us configure FC tape drives on our Solaris 8 and 9 servers? We are running Networker version 7.3 We cannot see the device paths of the drives using "inquire". We have run lus_add_fp_devs, the drives show up but not the paths. Persistent bindings are OK. The drives are not shown...

Hi, Has anyone out there configured an EMC CDL300 disk library using Commvault Galaxy? We will use the CDL as a virtual tape library rather than a mag-lib. We are having problems with Commvault talking to the CDL. Any help would be appreciated. Thanks in advance Superjan

Hi, Has anyone out there configured an EMC CDL300 disk library using Commvault Galaxy? We will use the CDL as a virtual tape library rather than a mag-lib. We are having problems with Commvault talking to the CDL. Any help would be appreciated. Thanks in advance SuperJan

The solution was to upgrade the version of Powerpath.