Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by superduperlopez

  1. superduperlopez

    CallManager 4.2 UDL file

    Hi, Does anyone know how to "force" CallManager to create a UDL file? or where this file lives? I have done a file search on the CallManager server and can't find it anywhere. Thank you
  2. superduperlopez

    Linking CallManager 4.2 to AI Office

    Hi, Has anyone out there successfully linked AI Office to Cisco CallManager 4.2? Aparantely I have to link the AI Office collector to a .udl file created by CallManager. I have done a search for any such a file on the CallManager server but there are none. Anyone has any ideas about how...
  3. superduperlopez

    Can't route VoIP traffic over VPN

    Hi, I wonder if anyone could give me some light regarding the following In one site I have a 2811 and in the other site I have a 2811 with a PIX506E. Both routers are running CallManager Express with IOS versions: c2800nm-adventerprisek9-mz.124-4.XC4.bin...
  4. superduperlopez

    GFI Fax traffic routed to Modem WIC-2AM

    Hi, We have Cisco CallManager Express installed in one of our sites and I was wondering if the following would be possible... The customer has a GFI Fax on-site, can I route the traffic to this GFI Fax through a Modem WIC-2AM card and if yes, I would appreciate some hints for the...
  5. superduperlopez

    7914 Expansion module - lights are NOT chaging to green or amber

    Hi, I have a 7914 Expansion module installed next to my 7960. The expansion module seems to be working fine ... besides the lights... According to Cisco documentation the lights should do as follows: Off/dark Line available Green, steady Line in use by you; you may also transfer the call...
  6. superduperlopez

    Cisco 7914 - expansion module - all lights solid red

    Hi, I am trying to get an expasion module 7914 to work with my 7960. These are some extracts from my config: CONFIG (Version=4.0(1)) ===================== Version 4.0(1) Cisco CallManager Express load 7914 S00104000100 load 7960-7940 P0030702T023 At the moment when I go into the...
  7. superduperlopez

    857W wireless router drop signal whem moving from one floor to another

    Hi, I have recently installed two Cisco 857W wireless routers and after installing them at two different houses, I am having exactly the same problem in both instances. The problem I am experiencing is the lack of signal as soon as I move into a different room/floor. In one of the cases, I...
  8. superduperlopez

    Debugging problem

    Hi, I am expereincing the following problem with a Cisco 1701, flash:c1700-advsecurityk9-mz.124-5.bin. I telnet into the router, type the terminal monitor command and then the fun begins...... if I do a "debug ip icmp" and do a ping somewhere I get the following... TEST#debug ip icmp...
  9. superduperlopez

    Load balancing over two ADSL lines

    yes, both Dialers are bound to Virtual-Access 1 and 2 respectively ...and after applying the "ip load-sharing per-packet" on both Dialers.....still the same any more ideas?? cheers
  10. superduperlopez

    Load balancing over two ADSL lines

    Hello again, The router is a 2621XM I am not doing any VoIP interface ATM0/0 no ip address no ip redirects no ip unreachables no ip proxy-arp no ip mroute-cache no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 2 ! dsl operating-mode auto no...
  11. superduperlopez

    Load balancing over two ADSL lines

    sorry I forgot to mention in my previous post.......... would "Multilink PPP" be an alternative??? cheers
  12. superduperlopez

    Load balancing over two ADSL lines

    Hi, I need to load balance traffic from one router over two ADSL lines but I only have control over the on-site router, not over the ISP router. Is there a way of doing this...I've been reading trying to find some information regarding the subject but in all the papers they seem to think...
  13. superduperlopez

    HSRP problem

    I have two 837s running HSRP. Both routers are connected to a 2960. Router_1: interface Ethernet0 ip address 192.168.0.2 255.255.255.0 no ip redirects standby 1 ip 192.168.0.1 standby 1 timers 254 255 standby 1 priority 111 standby 1 preempt hold-queue 100 out Router_2: interface...
  14. superduperlopez

    HSRP - lossing 50%-75% of packets when pinging

    Hi, sorry that was a typo mistake......a copied and pasted... I was already using 192.168.0.2 on the Ethernet interface for Router-1
  15. superduperlopez

    HSRP - lossing 50%-75% of packets when pinging

    Hi, I'm running HSRP in a small LAN.... I am using two 800 series which are connected to a 2960Switch... the configuration in the routers is as per below.... For Router-2: interface Ethernet0 ip address 192.168.0.3 255.255.255.0 standby 1 ip 192.168.0.4 standby 1 priority 200 standby 1...
See more

Part and Inventory Search

Back
Top