If two drives of a three drive RAID-5 are in missing status then OMSA should see the array as failed. Is that the case?
It should be OK to import the foreign config as it's still the original disks. The array then returns to degraded. Replacing the orange flashing disk will get it back to...
I see your post is nearly two weeks old now. Did you fix it?
I would have suggested the long init and audit as well. If that didn't work then watch a failing mount/dismount at the LCU CCTV monitor and see what the physical symptoms are (such as cartridge fouling at entrance to tape drive). The...
Drive comm error is usually an issue with the serial comms link between the drive and library controller.
1. First try re-seating the tape drive.
2. Get the drive and/or library up to latest firmware if either are downlevel.
3. This is the most likely: the drive has an internal problem causing...
Your first action with getting a 9310 status report is to log into the LMU utiliy <UTL> envionment.
Type ST DEV=0 (where the zero means LSM 0, change as required).
You will get a report on the status of all important parts, either OK (which is good) or INOP (which is bad).
3087 An excessive reach position error was detected during motion.
309E The door is open.
3E14 Drive 0 Connection State Transition - Drive not connected.
3007 Lbrary IPL has started.
3204 Failure encountered. See prior FSC codes.
3202 The Arm failed initialization.
308F The range of motion on...
Looks like it's cleared then. L700's do give some strange faults. Aside from the help you get from FSC codes, the best time to analysis problems is at time of failure, checking if it's a range of cartridges, or a specific destination column, or when unloading specific tape drives, verifying top...
Anu6006,
It's likely your L700 has a faulty hand. The 309D indicates that when the hand arrived at the slot, the cartridge present sensor is telling the controller that the hand is already empty.
You can elimiate any logical software error by looping the get/put diagnostic from the LCD panel...
Hello ddeblance,
An independant STK maintainer cannot upgrade your 9310 to 450 exchanges (at least not in the approved way). It's done by the customer getting in touch with his Oracle sales rep, who generates a code on an internal Sun system which is based on the machine serial number. A CE...
Firmware V87G0 is available for download at the IBM support website. ITDT ver 6.0 is available for download also. The blurb on the ITDT download page says:
"The ITDT Tool offers multiple functional capabilities that simplify the task of updating tape and library firmware. It is available for...
Hello,
Before taking this advice, maybe wait for another poster to confirm, as I've not tried this. As I understand it, the only difference between normal IBM LTO firmware and the flavour used with StorageTek libraries is the tape drive TTI serial interface. The STK version of LTO firmware...
I don't know any way to send PDF's or other files using this forum. Hopefully the OP's library will be at the level he needs. The only way to get firmware from STK/Sun/Oracle is either buy it from them or get it for free by taking out a maintenance agreement. They just won't let you download it...
To test an L180 you need to put a barcoded DLT or LTO or STK cartridge into a user cell and run about 200 passes of the demo test, which is under diagnostics on the LCD menu. That will check the hand, cable & controller card.
To check the host interace, attach it to a PC running Windows server...
That's easy. Take the cartridge out the CAP. Open the drawer and fill up the L20 with your tapes. Bear in mind that a standard L20 is actually an L10. The right hand slots only work if you have the capacity increase dongle in the back. The L20 is just a dumb changer to after that its up to the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.