Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by speed0920

  1. speed0920

    4000 hunt

    "Thanks for your help. I did a test yesterday—after adding GRPCAL to the COS list, the other extensions in my AUN group also started ringing, even though their COS lists don’t include GRPCAL. I’ll find time to test it again."
  2. speed0920

    4000 hunt

    “Is there another way to make this work? I have one digital extension and one analog phone. When I call the analog extension, I want both phones to ring at the same time. Also, I need both of them to be able to be picked up by other people too.”
  3. speed0920

    4000 hunt

    "In the SA configuration, we set up call resonance for extension 969 like this: ADD-SA:VCE,969,,,0,366,PRL,0," ",,,,,,,,,,EXT,NONE,1-1-101;. But others in the same hunt group can’t pick up calls to extension 969—they can pick up calls to 366 though. Has anyone run into this kind...
  4. speed0920

    SA Hunt

    Thanks for your help.
  5. speed0920

    SA Hunt

    “In the 4000 SA Hunt Group, where can I change the number of rings before it switches to the next extension? Right now it takes 8 rings before moving on.”
  6. speed0920

    siux3

    Alright, thanks
  7. speed0920

    siux3

    Hey there! I just added an SIUX3 card, and it's now showing a green light. 10 Q2287-X SIUX3 2 0 Q2287-X 1 -05 - READY ADD-BCSU:SIUP,1,2,10,"Q2287-X ",,0,2,0; Is there anything else I need to configure or enable to make sure everything runs smoothly? Let me know if I need to double-check...
  8. speed0920

    TMANI analog external line caller ID

    The system is 4000 V11. For the analog trunk format, my test on X8 shows DTMF. When adjusting the 4000 system to ETSI DTMF, it had no effect, so I chose ACTIDTMF instead. Everything appeared normal, and I rebooted the card after making the adjustment. Then, I encountered an issue: - After saving...
  9. speed0920

    Requesting support for STMIX

    "I just updated STMIX to the latest version, but the problem is still the same. Looks like this is going to be a hassle. Could this be related to the license? Right now, I'm using the free 30-day trial."
  10. speed0920

    Requesting support for STMIX

    I tested it, but I can't access sdat3—I can only get into sdat2. Is there a command to check if stmix is running properly?"
  11. speed0920

    Requesting support for STMIX

    Alright, thanks! I'll give it another try tomorrow
  12. speed0920

    Requesting support for STMIX

    "I know it's a Linux system. Based on my past experience, it should work after installation and setting up the IP, allowing access via the web. But when I checked the forums, I found that my system shows 'no Running LW,' which feels really strange. I've already unlocked the lock symbol, but the...
  13. speed0920

    Requesting support for STMIX

    I haven't tested this yet. I'm not familiar with SSH commands, but I'll give it a try. I haven't tested this yet. I'm not familiar with SSH commands, but I'll give it a try.
  14. speed0920

    Requesting support for STMIX

    "I’ve already unlocked the lock symbol, but the issue is still the same. At first, I thought my system wasn’t installed properly, so I reinstalled it and tested again, but the problem persists. However, the available LW on Flash shows as empty."
  15. speed0920

    Requesting support for STMIX

    From what I remember, in V8, once BFDAT, BCSU, and CGWB were set up, HTTPS access was available right away. In V11, I currently have STMIX LAN1 connected to the assigned network within the same subnet. I can ping it, but WBM won't open and the webpage isn't responding. Here’s my current test...
See more

Part and Inventory Search

Back
Top