Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by someguy758

  1. someguy758

    Epson TM-U220

    The shaft is actually lubricated and the cartridge head can move along freely. I tried a main board from another printer it worked but then died in the same way during the self test.
  2. someguy758

    Epson TM-U220

    I have an Epson TM-U220 printer which uses the idn interface to a Micros terminal, the issue is when the printer does not function. When the printer is powered on there is "ticking" sound coming from the cartridge head. The self-test does not work, the paper out light does not come on, the error...
  3. someguy758

    Call Forward/Redirect Caller ID

    Thanks for the response. I was able to use the Day and Night IDC to get it done so when they put the console in night mode a couple DIDs are translated to the DN for HMS so the caller id is the same and it all goes to the same mailbox.
  4. someguy758

    Call Forward/Redirect Caller ID

    Hi People, I am trying to get the Caller ID for the forward to DN and no the forwarded DN. System - Option 11C 5.0, E1, HMS400 I want to be able to forward or redirect calls from multiple phones to a DN which would go to HMS400, play a message / greeting and then the caller can leave a message...
  5. someguy758

    CS1K to SRG Auth Code

    I can already do that at the main site issue is getting some sort of pin/identifier for the user to dial in the CDR when the phone are in normal mode from the SRG.
  6. someguy758

    Second PRI Card

    yes i did
  7. someguy758

    Second PRI Card

    Yep.
  8. someguy758

    Second PRI Card

    Hello, I want to configure 2 PRI Cards in a CS1000E 5.5 1 of them to telco (E1) and the other to a E1 gsm gateway. The cards are in slot 3 and 4 of chassis. The one to the telco works fine but the other card wont even enable. I tried setting it up the second card as any other PRI. When i go to...
  9. someguy758

    CS1K to SRG Auth Code

    Hello, we have a SRG50 connected to CS1000E via SIP trunk. SRG Users currently use auth codes to dial out through SIP trunk to hit the SRG T1 to telco. Is there a way to get these auth codes into the CDR from the SRG or have kind of pin type identifier for users to be tracked when dialing out...
  10. someguy758

    Auth Code

    Hello, we have a SRG50 connected to CS1000E via SIP trunk. SRG Users currently use auth codes to dial out through SIP trunk to hit the SRG T1 to telco. Is there a way to get these auth codes into the CDR from the SRG or have kind of identifier for users to be tracked when dialing out through SRG...
  11. someguy758

    CS1K SRG50

    Hello, I have an issue the calling user id for outbound calls when in normal mode, it shows up as unknown thus having issues with call accounting for SRG. The calls go out via PRI to telco on SRG, main office is CS1000E v5.5 and using SIP. When i look at the line monitor i would see user as...
  12. someguy758

    NTAK79BCE5

    This card cannot work for the setup shown? If not, what is and where is this card primarily used? How is it configured? I have been unsuccessful in finding documentation on this card and how to configure it. Thanks
  13. someguy758

    NTAK79BCE5

    Hello, We have a NTAK79BCE5 2MB PRI card and trying to use it in a CS1000E v5.50J. When I try to enable in LD 96 i get; DCH000 . stat msdl MSDL 004 0 4 MAN DSBL .enl msdl 4 0 4 MSDL016 D-Channel...
  14. someguy758

    Call pilot mini

    it is 1.6
  15. someguy758

    Call pilot mini

    I am using call mini on cs1000e 5.5 and having some trouble getting the auto attendant to dial extensions including the operator. When an extension is dialed from there, there is a long delay and then it returns with the person at the extension is unavailable. Any suggestions on what is causing...
See more

Part and Inventory Search

Back
Top