Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by snor

  1. snor

    Can't find call diversion commands in mdsh

    Hi, "CD commands" for call diversion were changed : diversion diversion_common diversion_info diversion_system LC, AD, AD are still there. MDSH> lc lcdde lcddp lclde lcldp lcopi lctdi lctmp lcudi lcddi lcipe lcldi lcope lcopp lctdp lcude MDSH> ac acbge...
  2. snor

    BS332 upgrade firmware failed

    FYI: I had he same problem with some BS, I had changed this BS to newer one, then upgrade was OK. here, from release Notes R3G: Description of changes relative to version R3F Bug Not possible to download SW to DB1 under certain conditions Components: DB1 JIRA: RFP-115 Background: Under...
  3. snor

    connected devices

    Hi, BLFDP; sounds good to see, if there are digital Devices equipped or not (ELU28) Unequipped analog devices (ELU29) will not be shown with BLFDP. (manuell action needed, line by line) best regards, Norbert
  4. snor

    Removing a LIM from MD110 BC11 ecosystem... this is the right procedure ?

    Hi, try SFCEI; (after CNLIE:..) regards, Norbert
  5. snor

    MD110 CONSONO PROGRAMMING

    Hi, I not 100% sure, but I think this OPI console is a type 5 and should run on an ELU28. Take a look to the handset. The old OPI I (on ELU5) had a LEMO handset connector, the "new" OPI II (on ELU28) had a RJ10 (4Pin) handset connector best regards, Norbert
  6. snor

    change impedance 600ohms and 10kioms for tmu2

    take a look to the attached filehttp://files.engineering.com/getfile.aspx?folder=37175d81-052b-4ac8-9c7b-8ec54e285be4&file=TMU_strapping.PNG
  7. snor

    change impedance 600ohms and 10kioms for tmu2

    Strap 60 inserted enables 600 ohm impedance at input one. Strap 70 inserted enables 600 ohm impedance at input two. . Strap 60 removed enables 10 kohm impedance at input one. Strap 70 removed enables 10 kohm impedance at input two.
  8. snor

    change the country application systeme belgium to application system austria

    Hi, I think you will need the INL from application system Austria. VERSION=CXP1010110 There were some market specific parameters in program-units. (e.g. attenuation of different kind of trunks, etc.) regards, Norbert
  9. snor

    MD11 alias for esternal destination

    Hi, use a common abbreviated dialing number. 1.) NANSI:NUMSE=1555,NUMTYP=AC; 2.) ADCOI:ABB=1555,CLASS=0&1&2&3,TRA=xxxx-xxxxxxxx; --> everyone can dial 1555. (internal and also external) --> If you don`t want that all user can dial this number you can restrict this with the CLASS-parameter -->...
  10. snor

    MD101 BC11SP13 - 101 FAULTY CLOCK PROCESSOR

    Hi, FYI, looks like your spare part is also faulty or the boards (DSU and LSU) are not compatible. You wrote about a "R11" and "R7". Do the boards have the same ROF-Number ? There existed different board revisions (e.g.LSU ROF1314413/1 or /3 or /4) (and DSU ROF1314414/1 or /3 or /4) If I...
  11. snor

    No ring back tone in TDM extensions when dialing to SIP Trunk

    Hi Edgar, the RINGING to GSM and PANASONIC are a little bit different. PANASONIC sends a CONTACT header, GSM do not sned a CONTACT header. That`s the reason, while you can hear ring-back to Panasonic and not to GSM. In the past, MX-ONE didnot take care about this (before HF3) GSM Signal Nr. 5...
  12. snor

    No ring back tone in TDM extensions when dialing to SIP Trunk

    How I can see, you have updated your system from HF3 to HF4. Do you have a difference in the settings of sip_route ? e.g. in "profile" or "service" (sip_route -print -route xx -short) are the RINGING really "same" ? As I already told you, I have same problem with a SIP trunk to an IPC trading...
  13. snor

    Call supervision time

    ??? more information would be helpfull. TSW or TSE ? Version of the system Analog-, ISDN- or SIP-trunk ? ROCAP, RODAP, RODDP . Who does send release signal? --> a trace would show who release the connection. best regards, Norbert
  14. snor

    Used AASTRA MX-One

    Hi, I think the only one way to get the whished Information is to contact MITEL. http://www.mitel.com/ On this page you can find the contact for your region. best regards, Norbert
  15. snor

    Used AASTRA MX-One

    Hi Benami, first a little question, are you a Mitel Partner ? You will also need the documentation for the MX-ONE, called CPI (600Mb) This can be downloaded from a FTP-Server, but for partners only, as far as I know. Virtual appliance is also downloadable from this FTP-server. regards, Norbert
See more

Part and Inventory Search

Back
Top