Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by slapin

  1. slapin

    General Experiences?

    With reliable Internet or private IP, it does not make sense to run an on-prem PBX. Unless you have an office in the woods without any connection. I used to run a sizable Mitel shop. At some point we migrated to SIP trunking over private IP, and disconnected all PRI and POTS. After that it was a...
  2. slapin

    Converting wav files to 8K ulaw

    I use SOX if it is for converting only and no editing needed. Easy to script batches. http://sox.sourceforge.net/
  3. slapin

    smdr 1752

    You are risking to roll on something else. The system is using a lot of ports, so you may end up with a very obscure issue if you even manage to change it and it will be working. What is the reason to change it?
  4. slapin

    3300 CTI Event question

    Any specifics? Where the event is observed? Can you post an example?
  5. slapin

    Realtime SMDR

    @ mnpuckett Records are created upon the call completion. The question was how to see this at the beginning of the call.
  6. slapin

    mitel alarm no calls out or in

    Have you tried to contact telco? They can loop T1 up to the demarc and test. You can also make a loop and plug it into the port, you should get L1 up. Also in the error log you should see records indicating when the line went down.
  7. slapin

    3300 MXE DB Restore, without knowing original IP Addresses?

    You need to have appropriate licenses first. When you restore the database, it will try to consume licenses and if they are not there, the result will be at least unpredictable. If you have mos sheet or active AMC, place iBitton from the old system, get licenses and then restore the database.
  8. slapin

    Is there a limit on the number of digits in a speedcall number and if so can I change it?

    When Trunk group absorbs digits, the original DNIS is preserved, correct me if I'm wrong, so if there will be a conflict, the call will be forwarded to IQ anyway. Just a side note, I'm not trying to object the loopback solution, it was shared here previously and I used it with great success...
  9. slapin

    Is there a limit on the number of digits in a speedcall number and if so can I change it?

    IQ server can transfer calls based on DNIS. You mentioned that all the calls are terminated on the RAD initially, so this is a perfect use case. Also if you have SIP licenses, Asterisk can be used instead and you can create any DN transformations using dial plans
  10. slapin

    Minet delayed when ringing an IP set

    Yep, that is exactly what I have observed. Enabling STP at least for now will help you to find the loop as it will put some of the ports into the blocking state. The trade off is delayed startup until STP will resolve the topology behind the port. Since phones are rarely...
  11. slapin

    Minet delayed when ringing an IP set

    Actually CDP is used to identify L2 ports for emergency calls location and phones tracking, so it is at least accounted in the design and should not cause any issues in any average network. I have seen when 3750 will go crazy if portfast is enabled (STP disabled) and someone will plug a simple...
  12. slapin

    Minet delayed when ringing an IP set

    Then it becomes interesting. You say when you see a lot of traffic then it is kind of slow. In this case I would look for CPU load of the switch. Could be brodcast storm or loops. Try to establish continuous ping from a PC in the same segment to the controller and capture it in the wireshark on...
  13. slapin

    Minet delayed when ringing an IP set

    Still not clear where the ICP (The mitel box) is located relatively to IP phones. Phones will stream voice packets directly, but management and control will go through the ICP. So if the controller is reachable via MPLS, then management traffic will be affected and you may observe all sorts of...
  14. slapin

    Minet delayed when ringing an IP set

    You say IP trunks. Do you refer to 802.1q trunks where ICP is located in the same location as IP phones or IP trunks in terms of ICP or IP trunks as a connection from one location to another?
  15. slapin

    Realtime SMDR

    joebrown123, Can you telnet to ICP port 8001 from your PC? Maybe a firewall? Local IP is your PC and the configuration is needed to deal with the situation of multiple network adapters. As I said it is a proof of concept, so the application does not have a lot of utility facilities, hence no...
See more

Part and Inventory Search

Back
Top