Recent content by selcuks2001

Hello all, I cannot configure ssh on a Cisco 6509 switch. I cannot enter the command "crypto generate key" and similar commands which are needed to enable ssh on the seitch. Does anybody have an idea about the reason of that? Can it depend on the IOS software of the switch? Regards...

Hello Minue, Thanks for your reply. What kind of a WIC card do I need on my router in the central location? What can be the maximum speed on my central router with that card? I need at least 10Mbps speed in my central site. Regards b^2-4ac

Hello all, There comes my question: I have about 50 locations where I plan to put G.SHDSL routers which will connect to a central location. What kind of G.SHDSL routers do I need for these connections? In the remote and also in the central locations? The remote locations will have speeds...

Hello Jsteve, Thanks for your links which are very helpful. In your last link there are some MIBs to get the configuration file from a router. In those snmpget commands there are some parameters like: ccmHistoryRunningLastSaved.0, ccmHistoryRunningLastChanged.0, ccmHistoryStartupLastChanged.0 or...

Hello Jsteve, Thank you for you reply. I felt for the first time that I am too close to the solution with that link. =)) But in the link it doesn't say how to get the configuration with the snmpget command. There is some preconfiguration lines with the command snmpset to get the configuration...

Hello everybody, In the link below (Lemon13's link) I couldn't find any information about how to get the configuration file of a router using SNMP. There is only basic information about SNMP protocol used in Cisco environment. http://www.netcraftsmen.net/welcher/papers/snmprouter.html I don't...

M. Knorr's link? Lemon? Pardon? What? Regards b^2-4ac

Hello vipergg, I tried to do what is said in the document. But it didn't work. Anybody else can help? Especially somebody who has got some hands on experience on this topic. Regards b^2-4ac

North323, Assume that there is a router/switch. And SNMP is enabled on it. My question is if it is possible to get the configuration file from it via SNMP. Regards b^2-4ac

Hello everybody, How is it possible to get the configuration file of a switch via SNMP? Or is that possible? We assume that we know the community string and the IP address of the switch. Regards b^2-4ac

The IOS version is as follows. The latest IOS I've found in the web site of Cisco: c3550-ipservicesk9-mz.122.44.SE6.bin Below is the "show version" output. Maybe it can help also: SWITCH#sh ver Cisco Internetwork Operating System Software IOS (tm) C3550 Software (C3550-I9Q3L2-M), Version...

Attributes are as follows: Service-Type : Framed Tunnel-Medium-Type : 802 (includes all 802 media plus Ethernet canonical format) Tunnel-Pvt-Group-ID : 0x000008 Tunnel-Type : Virtual LANs (VLAN) A note: After I listened the IAS port with Wireshark I noticed an error about the attribute value...

Hello ADB100, Can you send me configurations of the switch and the IAS policies you are using? I am trying this thing with Cisco 3550. It works fine but I cannot realize dynamic VLAN assignment. If I assign the VLAN to the port manually it works but it doesn't when I want that IAS determines the...

Hello everybody, Well after some time the new problem seems to be a bit different right now. (Yeah, right. I'm still struggling with that 802.1x thing.) I could let the 802.1x concept work on my system. But thid time my only and only problem is that I cannot achieve dynamic vlan assignment. I've...

Hello underico, I cannot enter that command. The switch doesn't support this command. Do you think that is the problem? Regards b^2-4ac