Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by SamBvr

  1. SamBvr

    ARCserve 7 for NetWare

    I have a patch folder with the NLM's, documentation, PFC.ini, etc. I use for the state, no money to upgrade, I can email you all of the patch stuff I use for AS7. BeaversS@Michigan.gov Sam
  2. SamBvr

    Server console starts displaying alphabet & 0-9

    Terry, that's a possibility, this is 1 of 185 Dept. of Corrections servers I manage remotely. I'll investigate this as Corr does use MB.
  3. SamBvr

    Server console starts displaying alphabet & 0-9

    Server will display the following information after the command prompt at random when entering commands or just sitting? Please advise, thank you in advance. CORR_PCS_FS1:abcdefghijklmnopqrstuvwxyz 0123456789 ABCDEFGHIJKLMNOPQRSTUVWXYZ Server info: Novell NetWare 5.1 Support Pack Revision 08...
  4. SamBvr

    Selections for this device will be skipped

    This is also displayed in the BE Java App Server - thank you in advance Looking up remote object: rmi://122.21.42.2:10002/ServerImpl Server Initializing.... Server Ip Address: COR_xxx_SS1/122.21.42.2 Port Number:1234...
  5. SamBvr

    Selections for this device will be skipped

    One of our servers just started displaying this message: (c) 2004 VERITAS Software Corporation. All rights reserved. Backup Exec for NetWare Servers - Administration Console Version 9.10 Revision 1158 Server Edition...
  6. SamBvr

    AS9 PFC: Job queue needs to be fixed ARG!!!

    I have ran ASUTIL 20x and I still get this error on a NW6.5 Dell server. How do I completely remove AS9 to do a clean install? Thank you in advance, I'll slit wrists now... E21029 server does not have valid job queue or queue user for product BrightStor ARCserve - [-14]...
  7. SamBvr

    AS9 not finding replaced drive

    I had a thread in Dell servers forum, but now it looks like this is an application issue. So here goes: The loader was failing POST for the tape drive, so the tape drive was changed. Now I get errors; here is the scenario: Load tapes, starts inventory, "E-drive hndl error" displayed. I push the...
  8. SamBvr

    PowerVault 120T DLT7000 "E" - Drive Hndl error

    Thank you for the information, I spoke with tech from HP help center, and the DEC drive is not the issue, it's a high voltage drive and is okay in this configuration. It looks like it is an Arcserve issue not discovering the different/new drive. I may move this over to the Arcserve forum. ----...
  9. SamBvr

    PowerVault 120T DLT7000 "E" - Drive Hndl error

    I checked the CA page for compatible drives, the drive is listed as: Compaq/DEC TZ89 DLT E21V 35-70 GB, but does not have the footnote the drive is certified within an Autoloader. Could this be a firmware issue the table shows E21V as the firmware, if so what are the procedures to load the...
  10. SamBvr

    PowerVault 120T DLT7000 "E" - Drive Hndl error

    Part II - A friend of mine noticed that the tape drive is being seen as a DEC drive, not Compaq; could this be the problem?
  11. SamBvr

    Edit backup job

    I use Arcserve 7, or should I say the State does. Is there anyway to edit or view a backup job? I'm new to this, and it seems like I have to create a new job if want to make any change in what data I need backed up. Thank you in advance, ~ Sam
  12. SamBvr

    PowerVault 120T DLT7000 "E" - Drive Hndl error

    I'm new to all this coming from Field Service to Tech Services. I got the "Backups" job using Arcserve 9. The loader was failing POST for the tape drive, so the tape drive was changed. Now I get the subject error. Here is the scenario: Load tapes, starts inventory, "E-drive hndl error"...
See more

Part and Inventory Search

Back
Top