Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by RonyKassam

  1. RonyKassam

    Hipath 4000 adding New Features

    Can you please provide me with the commands needed to setup that. Also please I need the commands to make specific level in operator (like F3)
  2. RonyKassam

    Hipath 4000 adding New Features

    Dear sbcsu, Thanks for your reply. Yes, I get dial tone from GSM box. But I can’t choose this GSM from the operator. I need to change the numbering plan to let the operator choose this GSM port. I don’t know how? Because of that, I need to know how to setup 6 GSM ports only for dialing mobile...
  3. RonyKassam

    Hipath 4000 adding New Features

    Dears, Greetings... I have HiPath 4000, There are four features I have to setup: - adding 6 port (in SLMO card) to work with GSM modems, I mean when operator call for 09* it will be forward over the new 6 GSM ports. - adding 1 port GSM separated from the previews 6 ports, this port will appear...
  4. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    Dear Sbcsu, Thank you.
  5. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    Dear sbcsu, The cards location as to documentation (I've check that many time): Hard Disk/MO 19 HUBC Card 43 ADS DPC5 Processor (12270-x100-08 dpc5) 46 A Side Processor same as above 58 Q2113-X100-03 QDCL 70 Q2234-X100-06 SICOE 79 Q2224-X001-04 MTSCG 85 B Side Processor same...
  6. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    OK, I think there no choice without new HD, but please I need some details "Make a new disk using PCHI" How can PCHI get the instillation file or boot image? I don't now the steps to make new HD in PCHI? "or copy from MO each area to a newly formatted disk." I have MO with files like the files...
  7. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    Dear sbcsu, this is Yota as attached file. it is appear two time. what I have to do if its appear again? http://files.engineering.com/getfile.aspx?folder=b8f76447-ab5b-458f-be5e-ca81ccfb9130&file=20150330_173323.jpg
  8. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    After 10 minutes the symbol on CC-A is: 0 -> 1 -> 0 -> 4 -> 1 -> (three dashes above each other) -> same repeat. what does it mean?
  9. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    without HD-F-AREA -> MO-F-AREA And I don't have Hicom 310
  10. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    Dear sbcsu, after removing CC-B, the CC-A has the shape "1", and it still on "1", I don't know what is "yota" so, I will change the HD, but How can PCHI get the instillation file or boot image? I don't know the steps in PCHI? "or copy from MO each area to a newly formatted disk." I have MO...
  11. RonyKassam

    Re-install Unixware after "Activation of First installation was Failed"

    Dear sbsu, The REGEN file have been made by the command: <START-REGEN:USERCODE=FS,SYSNO=L31905Z0045A00001,CONT=N,PROT=N,UNIT1=ALL; START-REGEN:USERCODE=FS,SYSNO=L31905Z0045A00001,CONT=N,PROT=N,UNIT1=ALL; H500: AMO REGEN STARTED H01: REGENERATION STARTED H13: HW MODULE SWU IS NOT PRESENT AND...
  12. RonyKassam

    Re-install Unixware after &quot;Activation of First installation was Failed&quot;

    OK, I think I understand REGEN, you mean All amo commands that I need to add all the cards and trunks .., so I think it is like the file attached, but you tell me that I have to make this file like command in each line (without M1 1), so I can after that execute the command AMO by AMO (Line by...
  13. RonyKassam

    Re-install Unixware after &quot;Activation of First installation was Failed&quot;

    Dear Sbcsu, I have some questions about your steps: "If you have a REGEN" What do you mean? which area on HD? "Make a new disk using PCHI" How can PCHI get the instillation file or boot image? "or copy from MO each area to a newly formatted disk." I have MO with files like the files on the...
  14. RonyKassam

    Re-install Unixware after &quot;Activation of First installation was Failed&quot;

    OK, I will start in preparing new HD, but I don't know the steps and which partition(s) I have to copy from the old HD. please help
  15. RonyKassam

    Re-install Unixware after &quot;Activation of First installation was Failed&quot;

    what I have to instead of GENDB? did the file APFEL.KONDA that it is come in floppy disk with hipath help me ?
See more

Part and Inventory Search

Back
Top