Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by robertdenker

  1. robertdenker

    Netbuilder II Ping Problem

    Problem solved! It seems that the problem was the wrong seeting in at the Client NIC. I had to set it manually at 10Mbps. Now it seems to work...
  2. robertdenker

    Netbuilder II PPPOE?

    I´m now have the same Problem! I´ve got an 8 Port NBII with 11.4 SW/NBDPE-DW Software Installet! In the PPPoE Service Menu aren´t any entries! Have someone news about this issue?! Greetings from Germany-Berlin Robert D.
  3. robertdenker

    Netbuilder II Ping Problem

    I´ve got a Netbuilder II (CEC 20, F.W. 2.7, Software v.10.1/Complete Protocols)Router with an Ethernet AUI Card! I connect the Router Card via a CenterCom 210TS AUI Transciever to a netgear 100 Mbit netgear switch (autonego). The Netgear Switch shows a "Link", but when i Ping from a client to...
  4. robertdenker

    Contivity Switch 1500/1510 Software Version

    Does anyone know where i can get the Software Version 4.70 for a Contivity Switch 1500/1510!? The latest Version which i can download is 3.60! But i think when i want to use PPPoe, DHCP-Client on WAN interface (as Private)... i need at least Software Ver. 4.5 or above! Is that right!? Does...
  5. robertdenker

    BayStack 28115 LED´s

    Many Thanks for your replay! Thats right! When i connect my 100MBit WS the Link LED is on! Now i have another question! I haven´t got the console cabel! connetction via Telnet doesn´t work, because the Switch cut the connetion! Is there a way to configure the switch without buy an console...
  6. robertdenker

    BayStack 28115 LED´s

    i finally brought an used 28115 ADV! After booting up, the Display shows "Operational:RUN! No Errors are displayed! But all LED´s on the ports are green! I can´t connect to the Unit! Does anyone know what this means when all LED´s leave in green!?
  7. robertdenker

    BayStack 28115, need Firmware

    Hi! I´m searching for the newest Firmware Version for a BayStack 28115 Switch, Version 2.1.1.6 And i´m also searching for the Windows Backend Admin Software! Does anyone know where i can get the software!?
  8. robertdenker

    Lanplex2500 Boot Failure

    Hi! I´ve got an 3Com Lanplex2500, and i´ve tried to update the Firmware! That Failed! When i now boot the Switch, the Message "Flash EPROM Checksum Failure"! How i can install an new Image or can boot the switch over the Network! I´ve tried the workaround from the Manual, which...
  9. robertdenker

    Routing with NBII 4-Port CEC20

    Yes x.x.x.1 is the IP-Adress of every port! All IP-traffic hast to flow from 1,2 and 3 to port 4, which is attached to an Linux-Proxy Server! Another problem i had post for a while is: When i attach the NBII to a PC with a X-Cable there are problems withe pinging the router, or other PC´s! A...
  10. robertdenker

    Routing with NBII 4-Port CEC20

    Hi! I´ve got an 4-Port NetBuilderII, and have problem with routing! I´ve got 4 Subnets, each on every port: !1 = 192.168.1.0 !2 = 192.168.2.0 !3 = 192.168.3.0 !4 = 192.168.4.0 The goal is to route all traffic from each Port only to the Port 4 (WAN)! The other subnets don´t have to be...
  11. robertdenker

    Building Filters with NBII don´t work!

    I need another help with building filters.. I´ve got 4 Cards: Port 1: 192.168.1.0 Port 2: 192.168.2.0 Port 3: 192.168.3.0 Port 4: 192.168.4.0 I want, that the router only routes from all Interfaces to the Interface !4 (192.168.4.1- connected to the internet router)! I tried the following...
  12. robertdenker

    Netbuilder II, 10Mbit Eth, Ping losts...

    I´ve make another trie with ataching the pinging Station over a hub with a 1:1 Cabel! There i dont have any losts! It seems to bee a problem, with the direct connection over a crossover cabel!
  13. robertdenker

    Netbuilder II, 10Mbit Eth, Ping losts...

    Yes i changed the Transciever and Cable too! Everytime the same problem.. i´m still confused
  14. robertdenker

    Netbuilder II, 10Mbit Eth, Ping losts...

    Hmmmmm.... I´ve pinged a whole night to the 10BaseFL, without any losts I only have problems with pinging to the 10Base2/AUI cards... I can´t belive that all cards are damaged.....
  15. robertdenker

    Netbuilder II, 10Mbit Eth, Ping losts...

    Hi again.. I´ve got a 4-Port NBII with CEC20 Bord! ..with the following boards: 1x 10BaseFL 2x 10Base2/AUI 1x 100BaseFX All interfaces work fine, only the 10Base2/Aui bord has problems! I have got a lot of packet losts, a average of 50% are lost by pinging! I have 4 other 10Base2/AUI boards...
See more

Part and Inventory Search

Back
Top