Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by rkfoley

  1. rkfoley

    Night Service

    Hello There! Sounds like you have night mode working the way you want. I will assume you used D:L 1-1 for each of the co's . . . During day mode you need to set call intercept extension to the VM Extension (probably 165) ... Set the Intercept to number of rings you wish ... and it should work...
  2. rkfoley

    Night Service

    Oh well. Guess they will just have to deal with it! <g> Thanks for all the help and ideas! Rick
  3. rkfoley

    Hello, I have a 1232 and TVS50.

    Thanks! Will attempt this ASAP.
  4. rkfoley

    Night Service

    I know the newer phones have a Day/Night button but do you need a new software release as well?
  5. rkfoley

    KX-TD1232 and Intercept ...

    Hello, Started having a problem this AM and to be honest don't readily see why. I have, during day operation, and intercept of 4 rings to the voice mail extension 165. The ports on the TVS-50 are set to immediatly answer. Today on several occasions, person that answers phone out this am, the...
  6. rkfoley

    Hello, I have a 1232 and TVS50.

    Hello, Yes ... I have programmed VMT many times ... I see from allot of tech articles that they refer to this as VMT and VTR ... sorry for the confussion ... We are using a VMT button. And all works well as this is a small office ... Problem we run into is during day operation if someone get...
  7. rkfoley

    Hello, I have a 1232 and TVS50.

    Hello and thanks for the reply. > Solution 1: You can swap the DND solid led and the FWD > blinking led in programming under additional function (on > newer versions?). > Solution 2: Newer systems (-5 and above?) have a preset > call forwarding setting under station setting # 1. I am running...
  8. rkfoley

    Hello, I have a 1232 and TVS50.

    Hello, I have a 1232 and TVS50. I recently added the TVS50 and all seems fine. I am getting one complaint. During the day when the system is not in AA mode individual extension are sent to the voice mail using the FWD/DND buttons. Folks are complaining about having that FWD/DND buttons light...
  9. rkfoley

    Need mailbox to answer CO lines.

    Hello, I did this same setup (except TVS50) this past week. I used night/day service button's. In night mode set D:L 1-1, for the correct co's, to the voice mail port. In day mode set the, I beleive it was intercept, to the number of rings you wish to have it go to the AA. And do not forget to...
  10. rkfoley

    Night Service

    Thanks for the response ... We ended up assigning two -one touch- buttons ... this works however the lights do not light and they are forgetting to change it from day to night (781 on second button) or night to day (780 on first buttone) as there is no visual indicator to nudge them ... any...
  11. rkfoley

    Night Service

    I have a KX-TD1232 -2 and would like to add a night service button. It looks however like this release did not support a night service button? We are using KX-T7230 phones. Thanks - Rick
  12. rkfoley

    PARTNER ACS EXTERNAL ALERT

    I just did this and made my own device. If you need help give me a call at 330-534-7552. Rick
  13. rkfoley

    ACS Backup/Restore/Upgrade/Remote Access Card

    Thanks. Checking another card would be the next logical step wouldn't it! <g> I have a VM card on the way for this unit. I will know then if it's the ACS or the card. Does $245 for a replacement card sound reasonable? It's the upgrade to R5 as well Backup/Restore/Remote Access. Thanks, Rick
  14. rkfoley

    ACS Backup/Restore/Upgrade/Remote Access Card

    I tried the other slot ... I've powered off so many times and tried again it's not funny ... is the card junk then or can the card be reflashed? Thanks, Rick
  15. rkfoley

    ACS Backup/Restore/Upgrade/Remote Access Card

    Are there any obvious things to check, other than a properly seated card, when you get the &quot;invalid card&quot; response when trying to perform a backup (#124) on ACS R4? It is the silver card that is -labled- &quot;Remote Access&quot; and has (&quot;Backup, Restore, Upgrade&quot;) written...
See more

Part and Inventory Search

Back
Top