Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by RioGrande75

  1. RioGrande75

    ISDN Phone

    Usually ISDN needs 2 pairs: ISDN
  2. RioGrande75

    ISDN Phone

    STMD module was mainly used for ISDN trunks but can be configured for non-buspowered phones too. As there were not many pure isdn phones on the market, the subscriber option was used mostly for isdn videoconference systems or servers with isdn cards. In fact this was long time before all of this...
  3. RioGrande75

    ISDN Phone

    What do you mean with "ISDN numbers"? Do you want a simple ISDN extension or a ISDN trunk (e.g. CO-trunk)? If you want a ext., you have to know if you want a point-to-point or a point-to-multipoint (bus) configuration.
  4. RioGrande75

    HIPATH 4000 v6 UPGRADE ISSUE

    1.) Afaik CP phones are supported from V8R1 on - so no support on very old V6. 2.) Acutal OS4k versions like V10R1/V11R0 require EcoServer. You can wire the LTUCA's directly to the backplane of EcoServer.
  5. RioGrande75

    Hi am trying to call office in different Pabx hipath 4000 and its response back on screen Do not disturb

    Then there is the feature DnD activated at the stn. in the other os4000. Check in destination switch with AMO ACDTA: e.g. DIS-ACTDA:STN,23200;
  6. RioGrande75

    Unify partner

    Or just contact a sales representative for your area.
  7. RioGrande75

    Requesting support for STMIX

    If you expect a licensing issue, just have a look at HISTA messages and Assistant main page. Afaik there are no extra licences needed for a STMIX board, at least not in V10. With V11 even the SLES-upgrade-protection lic's are not needed anymore.
  8. RioGrande75

    Requesting support for STMIX

    If there is something wrong in the linux os, I would not spend long time in tryin to repair it. Official way is to reset the board - which means a new os installation. This procedure is described in "OpenScape 4000 V11 Volume 4 IP Solutions Service Documentation Issue 13.pdf" in chapter "2.11...
  9. RioGrande75

    Requesting support for STMIX

    It seems, linux on stmix is somehow not ready. If you can login via ssh, u should be able to see status/repair it.
  10. RioGrande75

    Requesting support for STMIX

    On stmix there is simply a linux os running, just like on host, assistant, soco, etc. V11 runs OpenSuSe.
  11. RioGrande75

    Requesting support for STMIX

    Can u access stmix with ssh?
  12. RioGrande75

    Requesting support for STMIX

    Ahhhh... V11! Afaik, there is a parameter that opens direct access to stmix. For security reasons this is blocked in default setup. This explains lock symbol too, that I didn't see until now.
  13. RioGrande75

    Requesting support for STMIX

    For some reason the STMIX is not reachable in the LAN. Neither OS nor LW can be determined. Also the lock symbol next to the pen is strange. When you login to assistant via ssh, can you ping the board (192.168.206.200)? Pls. post RMX config (DIS-BCSU,DIS-CGWB,TDCSU,etc.). Maybe the config is...
  14. RioGrande75

    HiPath 4k Commands - V11 R0.22.2

    There are lots of manuals available for OS4k systems. One of them (its for V7 but V11 is not too different) is here for example. Another one covers all AMO's - but be warned, there are hundreds of AMO's and even more parameters (>100.000 I guess). I strongly recommend to start with a OS4k basic...
  15. RioGrande75

    Requesting support for STMIX

    Off course the stmix' LAN port has to be connected to the network. If there is no router, you have to assign a IP in the subnet of the assistant to reach it with GW-manager. Also upgrade the OS on the stmix with GW-Manager.
See more

Part and Inventory Search

Back
Top