Recent content by richdthomas

Hi unclerico, Thanks for confirming this, that'll be my next move. Thank you for your help.

Hi burtsbees, I wouldn't normally discuss this further, as I've changed the setting, happy with the result but I want to reach an agreement on the bandwidth command so that any one else reading this thread isn't mislead. I've read a few articles...

Hi unclerico, Thanks for that, I'll keep the autonegotiation rule of thumb in mind. Would a Cisco PIX 501 be able to pass traffic faster then 6Mbps. Many thanks for all your help, much appreciated :) Richard.

Hi burtsbees, I have set up a DHCP pool per IP address, as it was my way to issue a specific IP addresses to a specific MAC address. I don't know if there is a better way of doing this. The "bandwidth 2000" configuration on my outside interface is only used for reporting/measuring the...

Hi unclerico, Thanks for your reply. I've issued the "ip cef" command in the global configuration and both LAN interfaces. I've put the output of the show commands below. I then read your bit about the speed/duplex mismatch, so I did a no full-duplex and I'm now up to a 6Mb download speed :)...

Hi, Our ISP is now providing over 1Mb download speed and the Cisco 1721 router I have between our cable modem and LAN switch is being a bottleneck, so we can't benefit from the increased speed. When I connected my laptop directly to the cable modem, I got a 5Mb download and 0.5Mb upload. When...

Hi, I am trying to set up a pair of internal DNS servers (primary and secondary) on Sun Solaris 8. I do not need these servers to resolve real outside world DNS names like www.yahoo.com I simply need to specify a list of internal private IP addresses and private DNS names. E.G...

Hi, I am trying to rebuild the kernel for Red Hat Linux 6.2 with CONFIG_MODVERSIONS turned off. I have had a few items I needed to include and disclude to get the kernel in a reasonable state. I am now left with the following error: depmod: *** Unresolved symbols in...

Hi Victor, It turned out to be a problem with the sniffing machine, so I rebooted it and I get all the data I want now. Thanks for your help. Richard Thomas

Hi, I have been readind the documentation CD fine for a number of weeks now. It is now saying that the licence has expired and the web page says "This software has expired. Click Exit to exit the appilcation.". I did not see any requirements to register or anything for the...

Hi Victor, All of the ports are on the same VLAN, as I have not set up any yet. I have also checked and I do not have a vlan.dat file. Do you have any other ideas? Thank you. Richard Thomas

Hi Victor, I have tried to set this up today. The commands I used are as follows: monitor session 1 source interface fastEthernet 0/1 both monitor session 1 source interface fastEthernet 0/2 both monitor session 1 destination interface fastEthernet 0/23 This is to send a copy of all the...

Hi Victor, This is what I get when entering the exact commands that you entered: User Access Verification Password: NHDMZSwitch1>ena NHDMZSwitch1>enable Password: NHDMZSwitch1#conf t Enter configuration commands, one per line. End with CNTL/Z. NHDMZSwitch1(config)#int fa0/24...

Hi Victor, Thanks for that. How do I get into (port conf mode), I tried the following: NHDMZSwitch1(config)#interface FastEthernet 0/24 NHDMZSwitch1(config-if)#port ? % Unrecognized command NHDMZSwitch1(config-if)#port But as you can see, I cannot issue the port command. Thank you.

Hi Victor, Thanks for the advice on using the PORT MONITOR command. Please could you let me know if the switch needs a reboot to have theis setting come into effect. Thank you. Richard Thomas.