Recent content by RFWatts

Is there a PCN/PSN for firmware release 36? I'm not able to one. The release notes don't seem to indicate anything either. I tried deploying firmware 36 on some of my IPSI, and indeed it set the port negotiation back to auto. When I tried to set it back, it gave the error, "Disable auto...

Is there any interest in possible group discussions on IPSI technical info, Control Network routing, and issues and possible fixes? There is much buzz about various IPSI sanity issues, and it might be good to get some live discussion of other folks' woes and ails. Would any one be interested...

This is actually a very common problem...You a likely having IPSI sanity issues. IPSIs are EXTREMELY sensitive to network blips...even blips lasting less than one second! I have been working the same problem for months now. Avaya has told me that the problem is in my network, but I am still...

This sounds like your DOS filter is doing this. I have noticed that if the DOS filter is set to 0xFFFFFFFF, then pinging can produce these types of results. Typically, you will want to leave it alone. However, if you set the DOS filter to 0x00000000, then it should respond to all ICMP...

The problem has been resolved...Here's the scoop: Firstly, I was able to determine that not all transfers would fail...only transfers to a "sub-menu" would fail. Since this is PVM PC, it does not give the ability to add sub-menus. I accomplished this by using a phantom station (18) and...

I have a Partner ACS "Small Office" package that came with the 308 ACS processor, and Partner Messaging PC card. I have set it up as an immidiate auto-attendant. I can press a selector code and transfer out, but only as long as there is just one vm port (ext 78 or 79) being used. If a second...

AvayaEng I have a trunk group setup between my CM3, and an Asterisk box that I am labbing. On the CM side, it's setup as a basic h.323 ISDN trunk group similar to whatsanavaya's post above. You will need to make sure you use a compatible codec in you h323.conf (or oh323.conf) file...I ended...

Vamosalavaya Can you elaborate on you H.323 integration between Asterisk and Avaya? In particular, how have you configured you trunks on each side? I'm working on brining up an Asterisk box, and I would like to connect it to my existing Avaya Communication Manager switch via h.323. Any info...

Here's how I see it; Avaya makes a product, which has flaws (bugs) requiring service patches, etc. Now they are going to effectively charge the customer to get those?! It is simply irresponsible and questionable business ethics to market a product like that! I'm not a Microsoft fan, but at...

I think ipsisession is a 3.x and later command. You might try telnetenable -p <ip address of ipsi>. I believe that was the pre 3.0 command to accomplish this.

After reading my last post, I need to clarify my statement. Avaya is not going to (as far as I am aware) charge for the firmware, or access to the site. However, you will have to have a sold-to number in order to get firmware. It is also unclear if you will get access to all the firmwares, or...

You can also hook up a sniffer such as Ethereal to Ext1 or Ext2 and monitor the hosts. This will give you the IP addresses of the 8300, P300, MGP, and VOIP module.

Simply put, this is Avaya's way of protecting the bottom line of there business partners. Restrict the access to critically needed patches and software, and the customer will have to pay for it. This is also going to hurt the freelance consultants who are not officially a business partner, but...

You can actually change the IP address of the IPSI remotely too! That's why I asked if you were changing the subnet. Since you are keeping it on the same subnet, this is pretty easy to do remotely: 1. From your media server bash prompt enter ipsisession -p <current ip address of ipsi> 2...

Since you are on-site, this makes things a little easier: ***You will definately need access to Communication Manager to complete the switch*** 1. Busy-out the ipserver interface 2. change the ipserver interface to the new ip-address 3. via the services port, change the ip-address of the...